M3 Threaded Compression Fittings have compact design.
Ultra-miniature M3CB-1016-303 and M3CB-1018-2-303, available for 1/16 and 1/8 in. OD tube sizes respectively, are constructed of 303 and 316 stainless steel and employ Buna-N, fluorocarbon, EPDM, and silicone seals. Model M3CB-1016-303 has 8.4 m installed height and 5 mm hex size, while M3CB-1018-2-303 features 11.9 mm height and 6 mm hex size. Both fittings feature 0-3,000 psig inlet pressure...
Read More »
Air Sampling Pump features battery-powered operation.
Designed to run at 1 L/min, Grab Air Sample Pump collects air into sample bags to assess exposure from airborne chemical hazards. It operates on 9 V battery, yielding up to 1,000 L volume. Recommended for sample bags with up to 10 L capacity, process is complete when bag is properly filled. Pump suits areas where leaks, spills, or other potentially hazardous events have occurred and concentration...
Read More »
Pressure Regulator utilizes closed-loop technology.
Housed in IP65 enclosure, Series QPV provides high resolution pressure control. Output pressure is proportional to electrical command signal input and is unaffected by changes in supply pressure. Pressure is controlled by 2 solenoid valves; inlet valve operates proportionally to flow required to maintain system pressure. Variable orifice effect allows precise control of pressure at low flow...
Read More »
Slurry Pumps handle abrasive applications.
Bravo pumps suit fluids with high concentrations of sand and stones. Available in 5 sizes, pumps deliver between 470-2,000 gpm and handle liquids with pH values from 4-10. Units are equipped with 4-pole low speed motor and hydraulic components are made from Ni-Hard 4. Typical applications include dredging, cleaning of settling ponds, coal and ore slurries, bentonite, coal washing water, sewage...
Read More »
Accelerating Composites Production with Dielectric Cure Monitoring
This white paper provides an in-depth explanation of how dielectric monitoring works, and why it's the best choice for any company working with advanced composite materials.
Read More »
Electronic Pressure Regulator uses O-rings for seat.
Model QB3 incorporates electronic pressure sensor that detects downstream pressure at work port for accurate regulation. Replaceable O-rings for intake and exhaust valve are set into groove that captures O-ring, but leaves room to move slightly and seal correctly for positive shut-off. Regulator accepts 0-10 V or 4-20 mA command signal and provides analog output that corresponds to actual...
Read More »
Control Valve combines valve, actuator, and positioner.
FCV 1 in. control valve incorporates LVDT for detecting position; actuator; and electronics and pneumatics positioner to open and shut valve. Available in normally open or normally closed versions, product operates with command signal of 0-10 V or 4-20 mA. Valve position and Cv changes linearly over 0-19 Cv range.
Read More »
Vacuum DE Filters provide crystal clear water.
Fabricated from polyester fiberglass, diatomaceous earth (DE) filters feature open tank construction and vertically mounted flat leafs with filtering surfaces on both sides. They operate on vacuum principle and provide filtration down to 2 Ã-µm. Impervious to water treating chemicals, products are equipped with control panel and rotary cam switch for operation and come in sizes to handle flow...
Read More »
Retention Mechanism protects graphics card.
Board-level retention mechanism for PCI Express graphics cards protects against electrical interrupts and mechanical damage caused by system-level shocks and vibration. Flexible arm extends away from slot and includes molded post that snaps into notch on bottom of add-in card. Device solders to motherboard adjacent to x16 PCI Express card edge connector, and engages with hockey stick shaped hook...
Read More »
Copper Tubing is offered in exact straight lengths.
Exact Straight Length (ESL) Copper Tube is delivered to HVAC/R OEMs, mechanically straightened and cut to precise and specific lengths for production of heat exchangers, chillers, and heaters. Lengths run from 10 in. to 25 ft. with 3/16-1 in. OD. Tube is available in tempers of H58 drawn, H80 hard drawn, 050 light anneal, and 060 soft anneal that meet ASTM specifications B68 and B75. ESL is...
Read More »
Pumps suit coating and semiconductor applications.
With 1,200 l/s pumping capacity, TPH 1201 turbopump is designed for harsh-duty applications with rotor geometry that permits foreline tolerance of 0.5 mbar without requiring drag stage. Performance of TPH 2301 minimizes number of pumps required in semiconductor 300 mm multi-pump chambers. It delivers 2,100 l/s for Nitrogen and 1,950 l/s for Hydrogen and Argon, while offering more than 2,000 sccm...
Read More »
High or Low Volume Custom Crates and Boxes Available from Reid Packaging
Reid provides mil-spec crates and corrugated boxes in custom dimensions from single to triple wall and will even package them on-site. Check out the video to learn more.
Read More »
