New Fluid & Gas Flow Equipment Products

Video Filter/Drivers help minimize design and test time.

Lead-free Models FMS6143, FMS6145, and FMS6146 are 3, 5, and 6 channel, 4th order filter/drivers that eliminate need for multiple discrete components. By providing 8 MHz cut-off frequency and 48 dB stopband attenuation, devices meet standard definition video requirements. Internal diode clamps and bias circuitry enable units to accommodate ac- or dc-coupled input signals. Outputs on each device...

Flow Control Valves control air from cylinders.

Models JFC-4 and JFC-5 are combination needle and check valve flow controls used to control air flow from air cylinders. Units control speed at which piston strokes, either while extending or retracting, depending on location in circuit. They allow free flow from inlet to outlet past needle and check valve. In reverse flow, check valve is sealed and flow must pass through metered passage...

Pressure Regulator targets space critical applications.

Diaphragm pressure regulator Model PRD controls output pressures from 0-40 psig, with maximum rated inlet supply pressure of 300 psig. Both inlet and outlet ports are tapped 10-32 UNF. Suited for gas and pnemuatic applications, non-relieving, single-stage regulator is offered in brass, anodized aluminum, 303 stainless steel for corrosion resistance, and 316 stainless steel for high purity...

Coiled Tubing permits unrestricted flow in confined spaces.

Coiled Fluoroplastic Tubing is chemical-resistant, non-flammable, and has low coefficient of friction. Featuring multiple, retractable coils in single tube, it can be manufactured from Texfluor(TM) PTFE, FEP, PFA, and MFA in various lengths and ID sizes from 1/16-2 in. Non-wetting and non-leaching, tubing is available in resins with very low refractive index for applications where operator needs...

Hot Forging Process

Check out this white paper to learn about the benefits of hot forging.

Manifold accommodates 4 regulators.

Up to 4 Model QB3 electronic pressure regulators can be mounted to manifold, which offers common supply and exhaust port with individual controlled outlet ports to minimize plumbing. Model QB3 is capable of controlling pressure or vacuum electronically by accepting command signal of either 0-10 V or 4-20 mA. Pneumatic output is linear to command input.

Steam Traps eliminate superheat problems on steam mains.

Horizontal SS5NH and vertical SS5VH facilitate drainage of condensate from high-pressure superheated steam mains and turbines. They provide seal-tight shutoff with constant water seal and rotational seating design that eliminates concentrated valve wear. Its 3-point seating ensures steam-tight seal, even under no-load superheat conditions. Stainless steel products have up to 1,720 psig hydraulic...

Flexible Gasoline Vapor Recovery Hose is EPA-compliant.

Resistant to hydrocarbons, VRU Hose is made from clear polyurethane reinforced with orange ABS helix and has encapsulated soft-stranded copper grounding wire. UV-resistant product operates in -40 to +200Ã-

Pressure Relief Valve offers thermoplastic construction.

Designed with PTFE bellows stem seal, Type E Pressure Relief Valve is available with PVC, PP, PVDF, or PTFE body materials and EPDM, FKM, or PTFE encapsulated FKM o-ring seals. Valve, available in Ã-½-4 in. sizes, has no metal-to-media contact and is corrosion-resistant. Drilled to ANSI B16.5 bolt pattern, product can be installed in thermoplastic piping and metal pipelines. It is suited for...

Pressure Relief System suits hygienic applications.

Designed for use in aseptic and hygienic process conditions, Hygienic Opti-Gard features non-fragmenting, reverse-acting rupture disc with smooth, uninterrupted surface finish. It fits directly between ISO2852 standard food industry couplings and clamp fittings. With performance tolerance of 5% across burst pressure range and 95% operating ratio, product is supplied with Integral Flo-Tel...

Close-Coupled Pumps transfer high-solids content materials.

Offering flow rates to 1,000 gpm, MoynoÃ-® 2000 CC Pumps feature sealed, Ultra-DriveÃ-® gear-type universal joint drive train and rotor/stator pumping element geometry. ANSI flat face flanges are provided on suction and discharge ends. Single mechanical seals meet DIN Standard 24960 and ISO 3069. Pumps are suited for scum and grease pumping, lime slurry transfer and dosing, chemical...

ISO-Certified J&D Tube Benders Delivers Rapid Tubeline Fabrication Services

J&D Tube Benders' laser cutting and machining services provide accurate and complex features on tubes of all shapes and sizes. Check out the video to learn more!