New CF-S Horizontal Centrifugal Pump Increases Productivity through Optimization and Online Predictability
Provides duty points with flows from as low as 2.3 m3/h to over 4 000 m3/h and can reach heads in excess of 76 m. Designed for continuous pumping of highly abrasive and dense slurries and are available in range of liner material options. Ideal for grinding mill discharge, hydrocyclone feed, minerals processing, tailings, sugar processing and industrial applications.
Read More »
New 2SA Vertical Sump Pump is Available in Single or Duplex Type
Allied Pumps’ 2SA Vertical Sump Pump is designed for discharge of drainage, seepage water, effluent and boiler blow down. The unit comes with steel and cast iron basins, grouting frames and pit covers. For applications containing corrosive liquids such as alkalies and acids, units are constructed from special alloys.
Read More »
Sundyne's LMV 801 Line of Direct Drive Pumps adds a series of enhancements and optional upgrades.
Sundyne's LMV 801 line of driect drive centrifugal pumps now offer an optimized API 610 (OH3 or OH5) pump to address flows to 380 gpm (86 m³/hr), and heads to 720 ft (219 m), and a variety of optional upgrades, including the API 682 cartridge seal to prevent errors in installation and common seal failures, and the API 685 sealless magnetic drive to eliminate emissions and improve...
Read More »
Horizontal Vortex Sump Pump comes with back pull-out feature.
1600 Industrial Horizontal Vortex Sump Pump is designed to operate up to 250° F with flows up to 1600 GPM. Unit is available in 1620 and 1626 models and features cast iron, 316 stainless steel fitted, 316 stainless steel, Alloy 20 and CD4MC construction options. Model 1620 comes with 0.875 in. shaft diameter with 1.25 in. sleeve whereas 1626 pump has a 1.25 in. shaft diameter with 1.625 diameter...
Read More »
CMAA Crane Buyer's Guide
CMAA has organized this Buyer's Guide to promote standardization and to assist prospective buyer's of electric overhead traveling cranes in selection of equipment most suitable for their applications.
Read More »Hydronic Heat Pump features Aurora communicating controls.
Combining scroll compressors, R-410A refrigerant, and oversized heat exchangers, 5 Series 500W11 offers 14.0–17.5 energy efficiency ratio and 2.9–3.1 coefficient of performance. Wide range of operating temperatures and reversible control box enable unit to be used in variety of heating only or heating/cooling applications. All fault conditions are monitored by controller to ensure safe...
Read More »Battery Backup Pump Systems provide basement flood control.
In case of power outage or main pump failure, StormCell™ provides uninterrupted flood control for basements. These 12 V battery backup sump pumps feature professional-grade chargers (10 and 25 A models) and energy efficient DC pump for extended run times. Optional NightEye™ wireless technology allows for remote monitoring of pump system via tablet or smartphone.
Read More »
Flow Pumps safely transfer hot oil or hot water.
Available for flows up to 1,330 gpm, CombiTherm Plus hot oil and hot water pumps operate up to 360 psi and 450 psi, respectively. Cooling fans and large fins keep temperature around shaft sealing below 220°F, even at process temperatures up to 660°F. Heavy-duty centrifugal pumps are centerline mounted which allows thermal expansion without affecting shaft alignment. In case of...
Read More »
Packaged Heat Pump offers smart controls, remote monitoring.
York® Direct Fit™ rooftop replacement solution includes 3–8.5 ton packaged heat pumps; exact-fit replacement design matches units to footprints of other manufacturers' units. Simplicity Smart Equipment (SE) Controls facilitateÂ- system setup/optimization/monitoring, while optional Mobile Access Portal Gateway enables remote access. Other features include adjustable defrost...
Read More »Solids Handling Vortex Pumps have high-temperature design.
Handling clear or solids-laden liquids up to 200°F, 1–10 hp SVF High Temperature/High Endurance Submersible Vortex Pumps feature (NEMA) Class R motor insulation, rated for 428°F temperature rise, and offer motor protection via oil-lubricated double mechanical seal design with seperate lip seal. Vortex style impeller is mounted out of liquid flow path, andÂ- vortex pump design...
Read More »
Submersible Pumps handle temperatures up to 200°F.
Used to pump clear or solids-laden liquids up to 200°F, SKGF Series employs RAD-AX® Dual Shredding Technology, featuring radial and axial shredding elements of hardened 440C Stainless Steel (HRC 55), to obliterate difficult solids. Size of solids passage through impeller and volute, coupled to high-torque, 4-pole motor (2, 3,Â- and 5 hp), enable large solids shredding. Motor...
Read More »
Reduce Time to Market, Improve System Uptime with Dedicated Computing Medical Solutions
Embedded computing solutions from Dedicated Computing are designed to meet unique and specific requirements. As the preferred supplier to leading healthcare OEMs, the Dedicated Computing team of expert engineers gets your product out to the market faster while helping your company avoid costly validation and verification steps. Check out our video to learn more.
Read More »
