New Material Handling & Storage Products

Cart Pusher/Puller is offered in stainless steel.

Walk-behind, motorized CartCaddy is suited for pushing and pulling carts and wheeled equipment in order to prevent strains and pains on employees caused by manually handling carts. Stainless steel model is offered for food, pharmaceutical, and other sterile environments that prohibit paint and powder coatings. Variable-speed twist grips allow unit to maneuver up to 15,000 lb carts in tight areas....

Water Storage Tanks suit mobile applications.

Series HLT seamless, one-piece, molded linear polyethylene tanks feature molded-in legs for structural integrity and stability. Capacities range from 30-525 gallons. Painted steel bolt-down anchor straps are available for all sizes. Tanks are suitable for feeding pressure washers, concrete saws, or any mobile application that requires water away from traditional supplies. Various fittings,...

Fork Truck Attachment transports rolls to machinery.

Tip Lift fork truck attachment is suited for operations where rolls need to be transported to machinery where no overhead crane system is available. With 900 lb capacity, product is dependent on face width of roll to be handled. Unit is equipped with 12 V air compressor for operating pneumatic tooth release mechanism and probes of various sizes that accommodate different core sizes. Controls are...

Low-Profile Lift Tables offer pit-mounted lift convenience.

Offered in 9 models, lift tables have platforms that lie almost flush with floor so loads can be rolled directly onto lifts without need for ramps. Lifts have capacities of 2,000, 4,000, and 6,000 lb, travel of 33 in., and platform sizes of 40 x 48, 46 x 48, and 52 x 48 in. All come equipped with 1 HP, 110 V/60 Hz/1 PH remote power units that provide speeds of 35, 50, and 57 sec. Safety foot...

Customized Silicone Technology: For Today's and Next Generation Electronic Applications

This white paper provides and in-depth overview into the customized silicone technology for electronic protection.

Clamp handles large, heavy parts.

Series PFC Frame Clamp features wide jaw throat that accommodates large parts with simple tooling. Total clamping force of 11,250 lb is available 3.940 in. above tooling surface. Force is constant as jaws close through last 1Ã-

Hot Melt Tanks support extrusion, swirl, or spray applications.

Therm-O-FlowÃ-® PTFE-coated tanks come in 5, 7, and 18 liter models. Each includes gear pump with pressure controlled output, accurate temperature control, sensors for diagnostics and over-temperature protection, and LED display for system status. Two larger units also feature adjustable speed DC-drive motor and user-selectable set back. Available in manual and automatic versions, systems...

Floor Locks secure mobile equipment.

Flexello TLCH Series floor locks provide ready means of instantly securing trucks or mobile equipment in fixed position without raising it. Products bolt to undersides of trucks with top face 7 7/8 in. above ground. Freedom of movement is restored by using foot pedal. Products have top plate measuring 6 x 4Ã-½ in. with 5 x 2Ã-½ in. bolt pattern. Overall height in freestanding position is...

PCI Module offers sample rates up to 105 MHz.

Model 7631 Peripheral Component Interconnect module consists of one 16-channel multiband digital receiver and two 14-bit 80 or 105 MHz A/Ds for direct wideband signal processing within on-board Virtex-II field programmable gate array. GateFlow tool suite supports custom FPGA configurations, while software drivers for Windows and Linux allow full visibility into low-level source code. Assembled as...

Material Transfer System controls material flow.

Controlled Flow Material Transfer System is comprised of two major components: hood and spoon. In hood section, material from discharge belt is collected and concentrated. Material moving through chute is directed onto spoon, where it is softly and uniformly positioned on receiving belt. Regardless of existing belt configurations, material volume, velocity, and direction are fully controlled....

Cart transports 3,000 lb of dunnaged parts.

Tilt Shelf Cart has counterbalanced shelves that tip and pivot out of the way once product has been removed. Carts carry dunnage-cradled products to and from production area, with 6 casters for rolling and maneuvering up to 3,000 lb. Easy-Release Tow Bar hooks and unhooks from tugger and foot-operated floor stop keeps cart in place.

Precision Machined Parts for High Tech Applications

For precision and value that sets the standard for quality and craftsmanship, EGS Production Machining is the source for precision and value. Our extensive capabilities and dedication to customer service allow us to deliver the optimal manufacturing solution. See our video to learn more.