Material Handling & Storage

Oil Skimmer thrives in harsh wastewater environments.
Skimmers

Oil Skimmer thrives in harsh wastewater environments.

Oil Slider(TM) features flexible floating collector tube that snakes over and around debris to reach hydrocarbons and contaminants from water. It is built with continuous duty motor and stainless steel housing. Self-contained coalescing cartridge can be switched out in minutes and enables up to 10 units to operate at one time.

Read More »
Smart Lift floats loads in assembly systems.
Lifts

Smart Lift floats loads in assembly systems.

Computer-controlled iLift(TM) lifting and balancing system for assembly and material handling lets operators apply 2 lb of physical force to move 150-lb load at speeds up to 4.9 ft/sec. Float mode allows direct movement of loads without need to push buttons from central control position, thus shaving seconds from cycle times. In-line slide handle eliminates vertical overtravel. Lift can be...

Read More »
Vacuum Pumps are used for pick and place applications.
Handling Equipment

Vacuum Pumps are used for pick and place applications.

Fastbreak pre-assembled high speed blow-off vacuum pumps, levelers and cups are suitable for applications that require accurate part placement of irregularly shaped objects and/or rapid part release in dusty/dirty environments. Blow-off action continuously self-cleans vacuum lines to ensure positive release into nesting fixture for safe placement of parts. Applications include metal stamping,...

Read More »
Electric High Lift is available in 2 models.
Lifts

Electric High Lift is available in 2 models.

Maxx-Jack Electric High Lift is capable of lifting skids, plastic pallets, wire baskets and containers with open bottoms. Unit includes 12 Volt electrical system with battery and charger. Push button lift and lower control is located in handle, and magnetic backed remote lift/lower control with 6 ft. cord is optional. Electric High Lift, with 2,200 lb capacity, includes automatic floor lock.

Read More »
Scissor Lift is for low volume paint operations.
Lifts

Scissor Lift is for low volume paint operations.

Self-propelled, curved rail guided scissor lift can access both sides and ends of product as it travels on floor guide rail. This pneumatic/hydraulic powered personnel lift travels from lowered platform height of 31 ft to maximum raised operator platform height of 144 ft. Its 30 x 66 ft operator platform features 500 lb capacity. Unit can be rolled off guide rail and used as stationary scissor...

Read More »
Stackers

Stackers offer capacities to 4000 lbs.

Series W heavy-duty walkie stackers provide lift heights to 154 in. and operate from 24 volt electrical system. Comfortable dual twist grip controls forward and reverse travel. Buttons for raise, lower, and horn are located in center of handle for easy access. Button at end of handle reverses truck's travel direction away from operator should he/she come in contact with it. Speed cutout switch...

Read More »
Screw Conveyor allows auger changeovers in minutes.
Conveyors

Screw Conveyor allows auger changeovers in minutes.

Single person can easily handle washdowns, servicing, and auger changeovers of portable High/Low Mobile Helix conveyor in minutes. Total dismantle time is 5 min or less, without special tools. Conveyor ranges in size from 2-8 in. dia, can convey at rates up to 25 CFM, and is used in food, chemical, and pharmaceutical industries worldwide. Electric actuator raises and lowers conveyor, allowing it...

Read More »
Controller provides consistent repetitive dispensing.
Dispensers

Controller provides consistent repetitive dispensing.

Pneumatic Model Z620 controller, with z-axis motion, dispenses liquid to controlled height for filling and potting applications in automated lines and conveyor-fed stations. Unit is attached to Model DSP501A dispenser which controls dispense time and air pressure. Adjustable-height dispenser, secured to vertical stainless-steel rod, may be angled. Stroke adjustment is from 0.20 to 2.00 in....

Read More »
Reclaimers

System recovers oil after chip deoiling.

Centrifuge Recovery System cuts oils utilizing centrifugal technology. Depending upon metallurgy and viscosity of oil, solids can be removed to 2-5 micron with processing rates over 100 gallons per hour. Systems can be designed with ability to process water-soluble oils, synthetic coolants as well as cutting oils. Designs with virtually no fluid hold-up volume make it easy to move units to...

Read More »

All Topics