Material Handling & Storage

Rail Bearing Slide is available in 5 bore sizes.

Rail Bearing Slide is available in 5 bore sizes.

Series STP Rail Bearing Slide, originally offered with 8, 16, and 25 mm bore sizes, is also available in 12 and 20 mm bore sizes. All 5 sizes offer 3 travel lengths to fit various applications. Unit is designed with internal and external shock pads to eliminate metal to metal contact reducing noise and end-of-travel impact forces. Features include precise linear motion, twin cylinders, and...

Read More »
Self-Propelled Boom Lift is trailer mounted.

Self-Propelled Boom Lift is trailer mounted.

DINO 125T boom lift, with 24V battery-powered system, operates any place where overhead access is needed. It features 41 ft working height, 24 ft 7 in. outreach, and 474 lb platform capacity. Included hydraulic drive system enables lift to traverse job sites at up to 25% gradeability. Additional features include on-board charger, 2-speed boom motion control, and 360-

Read More »
Boom Lifts do not need extendable axles.

Boom Lifts do not need extendable axles.

Models 800S and 860SJ telescopic boom lifts are each housed on fixed 8 ft 2 in. wide frame allowing access to congested areas. Total lift cycle from ground to 80 ft and back to ground is less than 130 seconds. Model 800S features 80 ft platform height, horizontal reach of 71 ft, 1000 lb restricted capacity, and 500 lb unrestricted capacity. Model 800SJ features 6 ft articulating jib with 86 ft...

Read More »
Board Stackers offer design flexibility.

Board Stackers offer design flexibility.

On .100 in. pitch, single, double and triple row through-hole headers (MTSW Series) and stackers (ZW Series), surface mount board stackers (HW Series) and shrouded headers (ZSS Series) are available for board stacking. For micro pitch, board stackers are available on .8mm pitch (AW Series), 1mm pitch (MW Series), .050 in. pitch (FW Series), .050 in. x .100 in. pitch (DWM Series) and 2mm pitch (TW...

Read More »
Tap Dispenser fits on work benches and storage shelves.

Tap Dispenser fits on work benches and storage shelves.

Dispenser holds and organizes National Pipe Thread Taps (NPT) in sizes from 1/16 up to 2 in. Three drawer dispenser provides 29 compartments with ID labels for each tap size. Cabinet measures 14-5/8 in. wide x 7-3/8 in. deep, and 7-3/4 in. tall. Fabricated from CRCQ steel, it is suitable for use in industrial environments.

Read More »

Rodless Pneumatic Cylinder works in temperatures to 500 ºF.

OSP Series Thermocylinder can be used for door opening and transfer in extreme temperature applications. It uses heat transfer and thermodynamic principles to allow coolant to pass through entire length of cylinder. As coolant passes through, heat energy is absorbed and barrel behaves similar to water jacket. This keeps heat away from cylinder bore where plastic and rubber parts are used.

Read More »
Transition Guides feature snap-in mounting.

Transition Guides feature snap-in mounting.

cPCI-T Series(TM) Transition Guides are designed specifically for compact PCI (cPCI(TM)) applications, and are fully compliant to IEEE 1101.10 and PICMG 2.16 CompactPCI-® specifications. Manufactured from UL rated 94V-0, ABS material for rigidity and strength, cPCI-T Guides support rear I/O as well as modified architectures. Available in red or white, guides can be ordered with or without...

Read More »
Dispensing Head applies adhesive in small doses.

Dispensing Head applies adhesive in small doses.

Electromatic XVI adhesive applicator head works with cold adhesives, coatings, fragrances, silicones, marking inks, water, lubricants and similar fluids. Applications include packaging, product assembly, nonwoven products, carton and paperboard manufacture, and product marking. All wetted parts are stainless steel, with only one moving part and no seals or packings.

Read More »
Support Rails suit low profile applications.

Support Rails suit low profile applications.

PowerTrax(TM) shaft support rails are made of aluminum and manufactured with bolt-from-bottom design for systems requiring low profile components. Available with case hardened and ground shafting in 6 sizes, they are suitable for long runs where continuous rail support is necessary. Rails allow for installation in compact applications while maintaining precise guidance control.

Read More »

Grippers provide high grip force to weight ratio.

GRS Grippers, available in 5 sizes with 2 jaw travels per size, have hardened jaws and hardcoated bearing surfaces. Internal jaw seals resist contaminants. Tooling alignment is achieved through use of dowel pin holes in jaws and body of gripper. GRS grippers feature angled cam drive and parallel jaw motion. They are double acting for use in both internal and external gripping applications.

Read More »

All Topics