New Fluid & Gas Flow Equipment Products

Filtration System recycles aqueous cleaners.

Stainless steel filtration system utilizes double set of elements that can be exchanged in less than 5 min with small wrench. It reduces oils and soils that interfere with cleaning. Wash stays clean all the time, eliminating inadequate parts cleaning.

Label Holder solves problems in wash down areas.

Model B30 Bottom Load Label Holder eliminates saturation and bleeding of labels caused by washdown solutions entering through open top of top-load label holders. One-piece, sealed-at-the-top design shields labels from water, cleaning fluids, and dirt. Soft, integral bead under clear front window provides added grip to hold labels in place. Bottom opening allows promotional signage to hang below...

Meter/Dispense Valve suits highly repetitive operations.

Air-operated Model 2600-009 dispenses small measured volumes of lubricants or other single-component materials. It features hardened components, wear-resistant seals, and internal check valves to insure metered consistency. Positive displacement unit can dispense up to 0.33 cubic cm, and operates at material pressures up to 2,500 psi. It is quickly adapted to fixture, robot, or manual...

Camera-Microscope Adapter provides instant digital photos.

Digi-Mic Adapter allows user to attach any Digital Camera with lens filter thread to conventional or stereo microscope. Adapter's Field Of View fills entire camera chip in horizontal direction. Model DMA-1 is made specifically for Nikon Cool-Pix cameras with 28 mm filter thread. Model DMA-2 has 37 mm male lens thread that fits Sony Digital Cameras. It can be attached to other digital cameras by...

Understanding Water Hammer

DFT Inc's engineers have been working with professionals in a range of industries for decades, helping to identify and resolve the underlying causes of water hammer. In this eBook you will learn about many of these common causes, how they impact your system and some of the basic changes you can make to eliminate them. In this eBook you will learn: What causes water hammer and why it is such a persistent problem. The role design plays in reducing the risk water hammer poses to your system. DFT's professional recommendations for coping with water hammer.

Power Relay provides 20 million operations.

Series FTR-MY occupies 100 mmÃ-² of PCB area. Dielectric between coil and contacts is 3,000 Vac and surge strength voltage is 5,080 V. Coils feature 110 mW sensitivity and 54 mW operating power. Bifurcated, gold overlaid, silver alloy contacts have contact rating of 250 Vac/30 Vdc at 5 A, and 5 A max switching current. Relay comes in 1 Form A and is available for 4.5 to 24 Vdc operation with...

Double Check Detector Assemblies detect unauthorized use.

Sized from 2Ã-½-10 inches, DCDA units protect against cross-connection of non-hazardous water into safe drinking water systems. Able to monitor water leakage, they have FDA-approved epoxy coated ductile iron body and bronze by-pass, which houses water meter and double check valve assembly. Max working pressure is 175 psig, and operating range is 33-140Ã-

Silt Density Index predicts membrane-fouling potential.

AutoSDI (Automated Silt Density Index) predicts membrane-fouling potential for reverse osmosis (RO) installations. Test Unit eliminates need for stopwatches, graduated cylinders, wet notes, calculators, and labor. Within 15 minutes after pushing single button, product gives users relative value for amount of suspended matter in feedwater streams. Field-calibrated unit runs continuously and...

Knife Gate Valve has dual actuators.

Made of 2205 Duplex Steel, 48 in. valve handles corrosive and abrasive materials. Product has face-to-face dimension of 6 in. and assembles without welding. Controls automatically open and close valve to 85% of open position, allowing removal of material deposit on blade. Unit is controlled by 3 relays, 1 limit switch, and 1 timer, all appropriately interlocked. Solids accumulated on bottom can...

Snow Shield(TM) protects filters by melting snow.

Deep pocket design prevents snow from clogging air filters and diminished air flow into buildings. Design also provides constant drainage, prevents refreezing of snowmelt, and eliminates stagnant water pools. Extracting snow flakes from air as it enters buildings, product installs into factory built air handlers and field built HVAC systems. It is available in various panel sizes for 3,000-30,000...

Steam Trap is rebuildable and thermally jacketed.

Universal Mount UMT-TD Thermodynamic Steam Trap conforms to 2-bolt universal swivel mount connection pattern, allowing option of replacing or repairing failed traps without having to break piping. Thermal jacketing assures continuous operation, regardless of surrouding temperature or precipitation changes. Sizes include Ã-½, Ã-¾, and 1 in. Connector block is optionally available with...

Eliminate Expensive Repairs with the Hot-Shot Pipe Thawing Machine

The new Hot Shot Pipe Thawing Machine delivers an innovative and highly effective approach to thawing frozen pipes. Easy to use and versatile, it is loaded with robust features that further suit it to many challenging environments. To learn all about it, see our video.