Fluid & Gas Flow Equipment

Fluid & Gas Flow Equipment

Process Diaphragm Pumps provide smooth output.

Dec 05, 2001

LEWAtriplex(TM) Monoblock Leak-Free Process Diaphragm Pumps feature 1 crankshaft with cams machined to 120°, roller bearings on both ends, and shock-resistant sleeve bearings on connecting rods. Triple-throw crankshaft drives all 3 pump heads, and is fully immersed in oil. Pumps incorporate multi-layer PTFE or metal diaphragms designed to operate up to 20,000 hours without maintenance. They... Read More

Fluid & Gas Flow Equipment

Ball Valves handle corrosive and high-purity media.

Dec 05, 2001

Tufline full-port lined ball valves feature metal-to-metal body joint that controls compression of lining for heat and stress cracking resistance. Cast-in recesses and machined grooves lock lining to valve body and ball, making lining blow-out virtually impossible. Lining is unpigmented, chemically-inert virgin PFA. Both full-port and standard-port models conform to ANSI B16.10 dimensional... Read More

Fluid & Gas Flow Equipment

Air Dryers offer remote monitoring.

Dec 04, 2001

HPRplus Series refrigerated compressed air dryers have air flows of up to 3000 scfm. Acting as complete Air Treatment Stations, dryers deliver dry, oil-free, compressed air. Their design includes dryer and filter with HF Series Grade 9 Filter/Separator that removes bulk liquid and particulates to 3 microns. Refrigeration system features R404a refrigerant, low noise hermetic scroll compressors,... Read More

Fluid & Gas Flow Equipment

Hand Pump is for use with 15 to 55 gallon drums.

Dec 04, 2001

Zee Line Hand Pump offers variable flow rates from 9.6 to 15 oz per stroke depending on linkage pin placement and fluid viscosity. It features carbon steel, brass, and plastic construction, and is able to handle rigorous use. Curved discharge spout with garden hose threads allows pump to be used with standard hoses. Applications include manufacturing and plant management settings. Read More

Fluid & Gas Flow Equipment

Dispense Valve features drip-free cutoff.

Dec 04, 2001

Pneumatically operated 752V-UHSS dispense valve has no seals or O-rings to wear out. Amount dispensed is determined by combination of fluid flow rate and valve open time. Adjustable stroke control allows flow rate to be fine tuned, while open time is regulated in increments from 0.01 to 0.001 seconds with EFD VALVEMATE(TM) controller. Applications include automated assembly machines, XYZ tables,... Read More

Fluid & Gas Flow Equipment

Gear Pumps suit chemical processing industries.

Dec 04, 2001

Chemsteel® rotary gear pumps, with flow rates from 1.5 to 30 GPM and duplex capabilities, feature keyed helical gearing for noise reduction. They are available with 15 shaft seal options. Gear combinations include Ryton®, 316 SS Alloy C, Teflon®, and PEEK®. Chemsteel® Pumps can be close-coupled. Read More

Fluid & Gas Flow Equipment

Coolant Nozzle comes with tapped hole.

Dec 03, 2001

Press-In ScrewBall coolant nozzle presses into reamed hole and can be easily aimed up to 35 deg either side of nozzle centerline. Its threaded hole can be fitted with extension tube to shoot farther, or it can be plugged with setscrew. Nozzle is suitable for wide variety of applications where aimable coolant stream is required. Read More

Fluid & Gas Flow Equipment

Flat Nozzle is available with built in flow regulation.

Dec 03, 2001

Stainless steel nozzle creates air stream with broad striking surface when wide objects must be dried, sorted or cleaned. It has low sound level, low air consumption, and is available with flow regulation for optimal use of compressed air. Adjusting blowing force minimizes energy consumption and noise level. Nozzle withstands high temperatures and corrosive chemical environments, and satisfies... Read More

Fluid & Gas Flow Equipment

Flexible Hose Nozzle assists blowoff, cooling, and drying.

Dec 03, 2001

Model #1201F-12 flexible hose, small diameter, low thrust air nozzle delivers 6 oz. of thrust at distances of 12 in. using 9 SCFM of compressed air at 100 PSIG. Its compact 3/8 in. OD hose is fully flexible, but holds its position under full line pressure. Model #1201F-12 is suitable for parts feeders, vibratory bowls, packaging, and printing and finishing equipment. 1/8 in. Nozzle has NPT male... Read More

Fluid & Gas Flow Equipment

Dock Seals and Shelters keep out inclement weather.

Nov 30, 2001

Available for door openings from 8 x 8 ft to 10 x 10 ft, model D-150-XX dock seals and model D-750-XX dock shelters mount around door opening in dock areas. Seal is available with projections from 10 to 20 in. with 36 oz reinforced black nylon facing. Shelter is available in projections of 18, 24, 30 and 36 in. with 54 oz reinforced black nylon facing. Shelter includes 36 in. drop curtain for... Read More

Fluid & Gas Flow Equipment

Adhesive Dispenser is suitable for UV bonding processes.

Nov 30, 2001

Model 1500XL uses microprocessor-based timer and air regulator to control amount of UV-cure adhesive applied. Teach function makes it easy to determine correct amount of adhesive to use for any UV dispensing application. Deposit size can also be set with digital timer and fine-tuned in 0.1, 0.01 or 0.001 sec increments. To apply adhesive, user holds syringe like pen, places dispense tip in... Read More

Fluid & Gas Flow Equipment

Dispense System varies flow rate, shot size and mix ratio.

Nov 29, 2001

Program-A-Shot 997 dispenses 2-component silicone, epoxy or urethane for potting or encapsulation applications. Flow rate, shot size and ratio can be electronically adjusted to mix and match parts on same production line without reprogramming system. For example, bar-code reader could identify part, then direct system to use programmed profile that dispenses material at pre-determined volume, mix... Read More

Fluid & Gas Flow Equipment

Underwater Pumps run in air or can be submerged.

Nov 29, 2001

Model 893-09 or -10 pump has brushless 12 or 24 Vdc motor that can run in open air or fully submerged in water. Pump and motor are rated at 50,000 hr life, and produce 3 gpm at 1 ft head or 10.5 ft head at 0 flow. Pump comes with 3/8 in. OD smooth outlet and 3/8 in. female pipe thread inlet. Other size inlets and outlets for hose and threaded connections are available. Standard plastic components... Read More

Fluid & Gas Flow Equipment

Tiny Pumps dispense small amounts.

Nov 28, 2001

SV700 Series of inert, solenoid-operated micro pumps are suitable for dispensing re-agents, dilutants and lubricants. Pumps are less than 3 in. high, have diameter of 1.10 in., and dispense volume of 50-250 µL. Available with glass-filled polypropylene pump head and EPDM or viton elastomers, pumps are compatibile with wide range of fluids. Fluid connections include 1/4-28 flat bottom ports,... Read More

Fluid & Gas Flow Equipment

Filters are suitable for working pressure to 4500 psi.

Nov 28, 2001

PL Series Manifold Mounted Filters are available in 9 different sizes, allowing user to select most suitable model for wide range of applications. Filter elements are synthetic micro-fibre available in 4 different filtration degrees, in standard and high collapse configurations. Filter housings allow for installation of differential, visual or visual-electrical clogging indicators. Read More

Fluid & Gas Flow Equipment

Molded High-Flow 2-Way Valve uses no O-ring end fittings.

Nov 28, 2001

Created for use in high purity/corrosive chemical applications, injection-molded Furon® In-Line-1000 Valve provides true 1 in. orifice and angled actuator that promotes maximum flow (Cv-15). It is offered in pneumatically or manually actuated versions, and has maximum operating pressure and maximum back pressure ratings of 100 psi. Fluid temperature ranges from 40°F to 212°F. 1 in. Fine... Read More

Fluid & Gas Flow Equipment

Diaphragm Valves withstand corrosive environments.

Nov 28, 2001

All-plastic diaphragm valves for 3, 4 and 6 in. pipelines are suitable for control of liquids, gases, and slurries in both on/off and modulating services. Each has handwheel that opens or closes valve with minimal effort. Plastic valves will never fail, jam, stick, or freeze in position because of rust or corrosion; will never contaminate sensitive process fluids; and never need to be painted or... Read More

Fluid & Gas Flow Equipment

Coolant Nozzle fits machines and toolholders.

Nov 28, 2001

BlackEye has threaded hole which can be plugged with setscrew, making it suitable for toolholders with ports that occasionally need plugging. Nozzles are easy-to-aim replacement for brass balls which often move out of position while tightening lock-screw. To install, tighten lock-screw, then aim swiveling stainless steel ball with tip of Allen wrench. Rated to 150 psi, they are available in sizes... Read More

Fluid & Gas Flow Equipment

Pipe Fittings are designed for coolant nozzles.

Nov 28, 2001

DualFit pipe fitttings fit both NPT and BSPT metric pipe threads, thus solving incompatability problems when using NPT pipe fittings on metric machine tools. Compact size is suitable for tight spaces. Acetal version is rated to 150 psi and brass version to 1500 psi. Read More

Fluid & Gas Flow Equipment

Coolant Nozzle is for CNC Lathes.

Nov 28, 2001

Extended ball socket on BugEye coolant nozzle provides greater aiming range than company's plain ball style nozzle, while still remaining relatively compact. Nozzles are suitable for tool positions where tool tip is difficult to reach with standard screw-lock balls. Rated to 150 psi, nozzles are available in sizes to fit almost every machine or toolholder. Read More