New Fluid & Gas Flow Equipment Products

Y Strainers are suitable for liquid, gas or steam service.

Model 85 cast iron and bronze Y strainers handle aggressive industrial and commercial applications. Cast iron models are available in pipelines up to 10 in. in ratings from 200 to 500 psi, with threaded or flanged piping connections. Bronze strainers in pipeline sizes to 6 in., are available with threaded, flanged or solder-end connections, and are rated up to 225 psi. Strainers come with one...

Flexible Hose Nozzle assists blowoff, cooling, and drying.

Model #1201F-12 flexible hose, small diameter, low thrust air nozzle delivers 6 oz. of thrust at distances of 12 in. using 9 SCFM of compressed air at 100 PSIG. Its compact 3/8 in. OD hose is fully flexible, but holds its position under full line pressure. Model #1201F-12 is suitable for parts feeders, vibratory bowls, packaging, and printing and finishing equipment. 1/8 in. Nozzle has NPT male...

Pleated Filter meets ASHRAE 52.2 Standard.

Type DP8 pleated panel filter has media made from 100% synthetic fibers enhanced with electrostatic charge to increase efficiency on particles sized one micron and below. It meets MERV8 rating per ASHRAE Standard 52.2 and provides 30-35% dust spot efficiency per ASHRAE Standard 52.1. Media is pleated with galvanized steel expanded metal backing to form consistently shaped pleats and prevent rust....

Adhesive Dispenser is suitable for UV bonding processes.

Model 1500XL uses microprocessor-based timer and air regulator to control amount of UV-cure adhesive applied. Teach function makes it easy to determine correct amount of adhesive to use for any UV dispensing application. Deposit size can also be set with digital timer and fine-tuned in 0.1, 0.01 or 0.001 sec increments. To apply adhesive, user holds syringe like pen, places dispense tip in...

Rack System Design & Buyer's Guide

There is plenty to consider before setting up or replacing storage rack systems in your warehouse. This whitepaper contains a guide and general checklist of the most important considerations.

Dispense System varies flow rate, shot size and mix ratio.

Program-A-Shot 997 dispenses 2-component silicone, epoxy or urethane for potting or encapsulation applications. Flow rate, shot size and ratio can be electronically adjusted to mix and match parts on same production line without reprogramming system. For example, bar-code reader could identify part, then direct system to use programmed profile that dispenses material at pre-determined volume, mix...

Underwater Pumps run in air or can be submerged.

Model 893-09 or -10 pump has brushless 12 or 24 Vdc motor that can run in open air or fully submerged in water. Pump and motor are rated at 50,000 hr life, and produce 3 gpm at 1 ft head or 10.5 ft head at 0 flow. Pump comes with 3/8 in. OD smooth outlet and 3/8 in. female pipe thread inlet. Other size inlets and outlets for hose and threaded connections are available. Standard plastic components...

Gear Pump Gears are available in herringbone style.

Optional herringbone gears are available for extrusion, compounding, polymer extraction and transfer pumps. Gears increase discharge pressures, extend life of pump's parts, and provide equal bearing loading that reduces energy requirements, decreases temperature and shear to fluid, and decreases pulsations from gear pump. Applications include compounding, tape production, pipe production, polymer...

Tiny Pumps dispense small amounts.

SV700 Series of inert, solenoid-operated micro pumps are suitable for dispensing re-agents, dilutants and lubricants. Pumps are less than 3 in. high, have diameter of 1.10 in., and dispense volume of 50-250 Ã-µL. Available with glass-filled polypropylene pump head and EPDM or viton elastomers, pumps are compatibile with wide range of fluids. Fluid connections include 1/4-28 flat bottom ports,...

Filters are suitable for working pressure to 4500 psi.

PL Series Manifold Mounted Filters are available in 9 different sizes, allowing user to select most suitable model for wide range of applications. Filter elements are synthetic micro-fibre available in 4 different filtration degrees, in standard and high collapse configurations. Filter housings allow for installation of differential, visual or visual-electrical clogging indicators.

Molded High-Flow 2-Way Valve uses no O-ring end fittings.

Created for use in high purity/corrosive chemical applications, injection-molded FuronÃ-® In-Line-1000 Valve provides true 1 in. orifice and angled actuator that promotes maximum flow (Cv-15). It is offered in pneumatically or manually actuated versions, and has maximum operating pressure and maximum back pressure ratings of 100 psi. Fluid temperature ranges from 40Ã-

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.