New Fluid & Gas Flow Equipment Products

Filter Vent is designed for dry bulk material bins.

Fast Filter Bin Vent is made of carbon steel, with solenoids pre-wired and plumbed. It has smart timer, DP transmitter and digital readout. Vents are available from 400-2200 CFM with 79 to 430 sq ft of filter media. Vents are shipped complete with galvanized cages, bag cups, venturis, and 16 oz. polyester (dacron) bags.

Dry Air System can be placed at application.

Mini Pneudri Midas provides uninterrupted clean, dry, compressed air where needed. It incorporates high efficiency and particulate filters plus desiccant cartridge inside 1 module that lets contaminated, compressed air in and clean, dry air out. Unit is available with pressure dewpoints of -40Ã-

Lubrication System is designed for stamping presses.

MicroCoat Lubrication System ensures that stock is always coated with even film of oil. It uses precision spray valves and LVLP (Low Volume Low Pressure) air to apply consistent coat of oil without dry spots, dripping or waste. Valve operation is regulated with pneumatically operated controller. Individual flow controls allow each valve's output to be adjusted independently and provide control...

Steam Traps are suitable for large process applications.

Magnum Series traps can be supplied with up to 18 bimetallic elements for hot condensate flows as high as 149,000 lb per hr. User can add or delete elements to match changing conditions. Bimetallic element uses both thermostatic and thermodynamic forces to ensure optimal plant control with no loss of live steam. 5 models are available for differential pressures up to 320 psi. Stainless steel...

The Definitive Guide to High-Capacity Autonomous Mobile Robots

This white paper is a complete guide to understanding autonomous mobile robots and their crucial role in various types of material handling applications.

Isolation Valves suit tight-fit applications.

Model KV-2 inert, manifold-mount, solenoid-operated, two-way, normally closed isolation valves measure 6 mm in width. They have internal volumes of 10 microL at inlet and outlet and virtually zero dead volume. KV-2 valves feature all inert, internal wetted parts that are diaphragm isolated from coil assembly and other metallic parts. They are suitable for low volume fluidic systems.

Diverter Valves handle pressures from 0 to 15 psig.

Diverter Valves are constructed with cast-iron body and end plates, with one-piece ductile iron rotor to hold critical dimensions and resist abrasion. Features include guarded actuators, ledge design that directs material, and triple protected bearings. Available control options include manual, air cylinder, air operated rotary actuators, and electric actuators. Diverter valves are available in...

Valve Manifold features single mounting flange.

HM53 3-valve instrument manifold performs block, equalizing and vent requirements of differential pressure transmitter applications. It features non-rotating tip stem that provides tight, repeatable shutoff without galling or cross-scoring. Flange allows transmitter to bolt directly to manifold, which eliminates piping of excess tubing and nipples. HM53 is available in Hastelloy, Monel, Alloy 20,...

Submersible Pumps do not require cleaning.

N-Pumps employ open-type self-cleaning impeller, and while operating, each leading edge passes across sharp stationary relief-groove. This action ensures that rags, stringy materials and solids are sheared, cleaned from impeller and pumped away. Pumps maintain high level of efficiency, even in fluids with high solids and fibrous content.

Safety Valves are suitable for use in piping systems.

Figure 32, 42 and 42A Safety Valves feature stainless steel bases and discs, which provide long life and corrosion resistance. ASME Section I and VIII approved valves feature two-ring control for dependable pop action, seat tightness and repeatability. Cast bronze threaded valves with stainless steel base and disc are available in sizes ranging from 1/2 to 2-1/2 in. for pressures to 300 psi and...

Connectors allow for off-axis insertion.

P-lokÃ-® connectors with integrated RADSOCKÃ-® socket technology provide positive-locking, spring-loaded coupling. 8 AWG P-lok contacts handle currents up to 69 A while size 4 AWG handle up to 120 A. Features include hyperbolic stamped grid configurations and Push-Pull systems. Thermal rise data after 500 cycles of durability is as follows: Size 8 AWG socket has 38Ã-

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.