New Fluid & Gas Flow Equipment Products

Extender Module Tray includes cable management shelf.

Designed for rackmount transmitter/receiver modules, which are interconnected via CAT5/5e/6 cable, XTENDEX ST-C5RCK-12 allows up to 12 extender modules to be mounted in 2RU shelf. Tray is equipped with 11 blank front panel covers to hide open slots on tray and to prevent change in airflow through rack cabinets.

MERV 8 Filter is classified as green product.

Designed as value-added upgrade from standard MERV 8s, 30/30Ã-® air filter features radial pleat design that allows full use of all-mechanical media for optimal dust holding capacity. Maintained resistance to airflow and average pressure drop contribute to savings on heating/cooling. Rated to 2.0 in. w.g. without media pack failure, solution has 5-star ECI rating and comes in 2 or 4 in....

Lightweight Compressor targets medical applications.

Featuring 8.3 x 4.0 x 6.4 in. footprint, 2450 Series WOB-LÃ-® weighs 9.5 lb and produces low sound levels of 50 dBA at 20 psig. Monolithic head minimizes leak paths, while optional intake locations on side and bottom facilitate plumbing, and boltless construction minimizes vibration and noise. Max flow is 3.0 cfm and max pressure is 30 psig.

Vacuum Pump suits new semiconductor manufacturing processes.

Featuring modular design, iXH series of vacuum pumps meets increasing demands of emerging processes required for semiconductor manufacturing at 60 nm and smaller design rules. Gas Buster(TM) inlet purge helps deal with process byproducts and minimize system maintenance and Active Utility Control (AUC) includes idle mode for periods when pump is not in use. Pump mechanism can handle hydrogen and...

5 Key Questions to Ask Your Valves & Fittings Manufacturer

This ebook discusses the five key questions you can ask to avoid common pain points and find a manufacturer who will provide the maximum value and service for your components.

Proportional Relief Valve offers protection from 150-6,000 psig.

Available with 0.142 in. flow ports, HPRV, PED-certified valve features captured seat design that is blow-out and chip-resistant, as well as balanced poppet design for operation in back pressures up to 2,000 psig. Range of color-coded springs configure valve for 8 cracking pressure ranges, and fine adjustment is achieved by external nut secured by Tru-Loc mechanism and lock wire. O-ring seals...

Relay has maximum switching power of 60 W.

Series J860 monostable, high dielectric relay with 2.5 kV surge strength conforms to FCC Part 68. Measuring 15.0 x 7.5 x 9.5 mm, relay is DPDT with coil voltage choices of 3, 4.5, 12 and 24 Vdc. Featuring max switching voltage of 250 Vac, 220 Vdc and switching current of 2 A, relay has electrical life at rated load of 100k cycles and mechanical life of 100M cycles (typ).

New Hand Dryer Awarded Certification

Follows other awards and endorsements Atlanta, GA-February 12, 2008-Dyson, the famous English vacuum cleaner company, announces that their Airblade hand drying system has been awarded certification by NSF International. The Airblade system is marketed in the United States by Cannon Hygiene, Inc. This is the first and only such award the NSF has ever given to a hand dryer manufacturer. Formerly...

Air Nozzle delivers precision blowoff in tight spaces.

Measuring 0.78 in. long x 0.25 in. dia, Nano Super Air Nozzle(TM) Model 1110SS features Type 316 SS construction suitable for blowoff, cooling, and drying applications. Unit provides narrowly focused air pattern that measures 1.5 in. dia when positioned 6 in. away from target surface. Blowing force of 8.1 oz is achieved with air consumption of 8.3 scfm at 80 psig. Since airflow cannot be blocked,...

Compression Limiters absorb load in plastic assemblies.

Series CL500 roll-formed, insert-moldable Compression Limiters is designed around standard clearances for 6 and 8 mm bolts, while series CL550 is designed with additional clearance around bolts to accommodate greater positional tolerances. Standard material is low carbon steel with trivalent, hexavalent-free zinc plate finish for corrosion protection. They are used to preserve threaded joint's...

Hot Runner Nozzles come in 28 different sizes.

Available in lengths up to 250 mm, Value Shot Z202 Series includes tips made of molybdenum alloy, which offer thermal conductivity as well as abrasion resistance, and enable processing of filled molding compounds and engineering plastics. Nozzle tips made of CuCoBe are suitable for gating onto sub-runners or for direct gating with sprue. Also made of molybdenum alloy, open nozzle tips allow...

Reduce Time to Market, Improve System Uptime with Dedicated Computing Medical Solutions

Embedded computing solutions from Dedicated Computing are designed to meet unique and specific requirements. As the preferred supplier to leading healthcare OEMs, the Dedicated Computing team of expert engineers gets your product out to the market faster while helping your company avoid costly validation and verification steps. Check out our video to learn more.