New Fluid & Gas Flow Equipment Products

Filter System minimizes pressure drop.

Series 1000 HEPA filter system enables 60% lower pressure drop than conventional 12 in. deep HEPA filters. Compact filters are available for standard Air Handling Units as well as separate housings (with or without fans). Series 1000 HEPA filter has pressure drop rated at 0.5 in. WC at 2400 scfm in standard filter size of 24 x 24 x 11.5 in.

Pinch Valves handle aggressive, particulate-laden liquids.

Pinch valves offer inertness similar to isolation valves with straighter, no-clog flow path. They are available in normally closed or normally open position or in 3-way configuration for fluid switching. Valves accommodate tubing from .010 to .875 in. ID. They aid in purging waste lines containing aggressive, particulate-laden solvents, corrosives, reagents, or other liquids.

Pump Systems provide extra pressure boost when needed.

MiniBooster(TM) is offered in 1- and 2-pump packages, with simplex capacities from 20 to 110 gpm at boost of 20 to 55 psig, and duplex capacity that can reach 220 gpm. Both automatically adjust to system requirements, stopping during periods of low demand and restarting upon drop in system pressure. Close-coupled pumps have stainless steel casing and internals. Open, drip-proof motors range from...

Linear-Motion Stage includes multiple drive options.

EasyLinear(TM) Stage, made with customer-specified brand of profiled rail-and-ball slider, drops into place. System is ready for operation with addition of motor. Drive options available include multiple ballscrew leads, acme, hi-helix multi-start, lead screws with acetyl, and polymatrix nuts. Accessories include motor mounts for C-Face NEMA, Oriental, and European metric motors. Hand cranks with...

Ergonomics Is Good Economics

While you don't need an MD to know that ergonomic designs are good for physical health, you probably didn't realize that these designs can actually be good for your economic health too.

Lock Out Relays protect critical utility equipment.

Series 24 features manual, electric, or self-reset capability. They offer multiple decks and contacts and selection of trip and reset coils. Maximum of 10 decks can be stacked in single relay, providing up to 40 independent contacts rated at 60 amps for 1 minute and 30 amps for continuous current in range of 125-250 Vdc or 120-600 Vac. All Series 24 LORs are offered with built-in coil monitoring...

Ejector Headers mate with .050 , .100 , and 2 mm cable systems.

EHF Series double row surface mount ejector headers on .050 in. pitch are available in 7 pin counts from 10 through 50 pins. Mated height is .445 in. above board. EJH Series surface mount and through-hole ejector headers on .100 in. pitch come in 6 double-row pin counts from 10 through 50 pins, with mated height of .665 in. EHT Series surface mount, through-hole and right-angle ejector headers...

Wastewater Evaporator provides 100% removal of water content.

Thermo Ox Series 3 Dry Chamber Flash Wastewater Evaporator eliminates need to haul wastewater and problems of corrosion and slurry removal. It leaves dry ash in coated ceramic chamber, utilizes any BTU of wastewater for fuel savings, and can use used oil as fuel. Fully automatic unit is suitable for machinery coolants, PCB waste, textiles, heavy equipment, and machinery coolants.

Thermal Isolator extends temperature range of accelerometers.

Accelerometer Thermal Isolator (ATI) enables low-impedance output accelerometers to operate on test surfaces with high temperatures. It is constructed from 0.325 in. thick, amorphous polymer that is characterized by low thermal conductivity, chemical resistance, and natural flame resistance. Maximum service temperature is +171Ã-

Gear and Piston Pumps suit mobile and construction industry.

Gear pumps range from 2800 to 4600 psi while piston pumps produce up to 5000 psi. Dowel-pinned pumps are bi-rotational and available in both DIN and SAE shaft configurations. SAE and metric hose connections are also available. Gear pumps are available from 300 to 3000 rpm and piston pumps run up to 1500 rpm.

Reel is suitable for pressure washing industry.

Constructed of 12 and 16 ga steel, with black powder coat finish, PW Series reel mounts to almost any pressure washer. Rated for pressures up to 4000 psi, it handles product temperatures from 20 to 250Ã-

SRG Global Coatings Enhance Surface Durability, Efficiency, Design Flexibility

SRG Global's automotive coatings enhance the structural integrity of the finished part while also improving vehicle efficiency. Check out our video to learn more.