New Fluid & Gas Flow Equipment Products

Two-Component Pump aids tub and shower manufacturers.

Used for high-volume dispensing of filled polyester resin and catalyst material, Boss(TM) pump offers 5 gpm @ 20 cycles/min standard output and 15 gpm max output. It delivers uninterrupted operation and features reversible sharp-edge carbide seats, hard chrome-plated cylinder and rod, as well as spring-loaded u-cup seals with no packings. Additional features include integrated muffler in air...

Subminiature Solenoid Valve has in-line barbed fittings.

Available at either 3.5 or 0.9 W, SERIES 58 subminiature 2-way, normally closed valve measures 2 x 1 x 5/8 in. Max operating pressure is 300 psi, burst pressure is 1,500 psi, operating temperature range is -5 to 122Ã-

Strainer separates particles from fluid in drums/pails.

Hung from top of any open-headed 55 gal drum or 5 gal pail, EZ-Strainer(TM) insert strains unwanted particles from liquid without possibility of being pulled inside. It stays in place, even when used with heavy, viscous products and may be used with or without liner inside drum or pail. Molded from high molecular weight high-density polyethylene, it is available with center screen in 100...

Ratio Control System enables precise metering and mixing.

Used in single- or multiple-component applications, RCS 2 is suited for precise electronically controlled gear-pump metering and mixing. It features magnetically coupled metering pumps that eliminate shaft seal leaks and provides absolute on-ratio gear-driven 1, 2, or 3 k mixing and metering control. In addition to solventborne or waterborne materials, system can also be used with rotary...

Bearing Solutions for Machine Tool Applications

An in-depth overview of the types of bearings used in machine tool applications. Check out this eBook to learn more.

Air Filters feature self-sealing, leak-free design.

Designed with layers of multi-denier polyester fibers, Activator Series ring panels and links capture particles throughout filter's depth. Units come in 2, 3, and 4-ply models to meet requirements of MERV 6, 7, and 8, respectively. Media layers are heat-sealed around 9-gauge internal wire frame with cross wire supports to hold media in place. Tackified adhesive is applied to air-leaving side of...

Turbo Pump goes from atmosphere to high-vacuum.

Used as standalone unit or as backing pump for turbopumps, OnTool(TM) Booster pump provides one-pump solution for achieving high vacuum. It eliminates need for backing pump due to its pumping speed of 130 m-³/h and pressure of less than 1 x 10-5 mbar. Suited for clean applications that operate without any particulate matter, corrosive gases, or condensation, product produces minimal vibration...

Acrylic Sub Plates simplify fluid system design.

KIP series facilitate design and installation of complex media flow requirements. Use of acrylic base permits flow of various media through single base using multiple inlets and outlets. For design flexibility, flow paths can be varied and directed to match specific design requirements.

Electric Pump offers true positive displacement.

Sinks Smart Pump E2 provides users with positive displacement electric pump that addresses paint-specific needs of finishing industry. With motor frequency directly proportional to fluid output, product uses ac electric motor to maximize reliability while driving fluid section. It is suited for low-pressure circulating systems where paint specific needs for production, flow control, and long-term...

Multi-Mold Cassette takes indoor air quality readings.

Operating in accordance with fluid/air dynamic principals, dual M2 disposable sampling device reads indoor air quality in various environments. It utilizes standard pump and calibration equipment, with each cassette capable of collecting 2 different samples, collecting 2 identical samples concurrently, or collecting one sample while using other cell as control. Depending on environment, cassette...

Plastic Tubes target cosmetic/personal care market.

Available in wide range of diameters, lengths, and orifices, Polyethylene Plastic Tubes are suited for topical skincare, hair care, personal care, spa, and medicinal/healthcare products. Matching dispensing caps are offered in snip-tip, flip-top, disc-top, stand-up, and child-resistant models.

Standex Engraving Mold-Tech Offers Nickel Shell Capabilities on a Global Scale

Standex Engraving Mold-Tech is the premier, global supplier for mold texturing and surface finishing. With a full range of services, Standex Engraving Mold-Tech is also the only nickel shell supplier producing in three global locations. See our video to learn more.