Optical Sensor/Solenoid Valve aids in conveyor automation.
Designed for sensing objects moving through conveyor accumulation zones, OSV incorporates solid-state electronics and solenoid valve using logic and manual inputs to control pneumatic actuator. It detects variety of materials at distances up to 6 ft and may be cascaded up to 100 units. Along with modular design, product features multi-color LED indicators, self-aligning beam, adjustable valve...
Read More »
Wave Soldering Systems utilize lead-free upgrades.
Electrovert EconoPak GoldÃ-®, ElectraÃ-®, and VectraÃ-® Wave Soldering Systems may be fitted with UltraFill(TM) Nozzle, designed to increase contact length and dwell time. Nozzle also reduces temperature drop so that minimal superheat is needed to reflow solder joints in second wave. Also available, Quick Change Solder Pot provides capability to switch between 2 alloys. It includes...
Read More »
Process Display offers pump control and batch functions.
Featuring 7-digit, 14-segment, multi-colored LCD, Model RIA452 comes in panel-mounted housing for monitoring and displaying analog measured values. It offers up to 8 relay outputs for pump control functionality, and analog current input of 0- or 4-20 mA, which can be supplied as intrinsically safe for use in hazardous areas. Four digital status inputs indicate failure of controlled device, and 2...
Read More »
Mixing System offers 600 gallon capacity.
Designed for operation under full vacuum conditions, Dual Shaft Mixing/Dispersion/Control System consists of slow speed anchor with hinged TeflonÃ-® wall scraper and high-shear rotor/stator mixer. It includes self-contained vacuum pump, and piped skid system with minor metering systems for minor liquid additions. Control panel controls mixing process including automatic metering, mixer speed,...
Read More »
Ergonomics Is Good Economics
While you don't need an MD to know that ergonomic designs are good for physical health, you probably didn't realize that these designs can actually be good for your economic health too.
Read More »Fittings feature snap-in design.
Made of die-cast zinc, WHIPPER-SNAP(TM) Connectors feature hardened spring steel locking ring that eliminates need for locknut and installs in seconds. Double locking tabs hold connector tight in box, while additional tension tabs provide continuity and clear wire path. Push-through design eliminates snags and wire damage. WHIPPER-SNAP(TM) connectors are UL listed for grounding when installed in...
Read More »
Flushometer conserves water in commercial applications.
Flushometer features UPPERCUT(TM) Dual-Flush Handle, which gives users 2 flush options: tilting up for liquid waste, or pushing down for standard flush. Former releases half of standard 1.6 gal flush. Users can choose complete UPPERCUT Dual-Flush Flushometer or UPPERCUT Dual-Flush Handle retrofit kit. Green handle features antimicrobial coating for protection against germs, and flushometer comes...
Read More »Tee Valve is designed to minimize potential accidents.
Suited for continuous flow applications, Tee Valve assembly includes Type 546 ball valve connected to tee by reducer bushing. Safety plug, shipped on open end of valve, prevents leakage if valve is left open when system is started up. Available in PVC and CPVC body materials with EPDM valve seals, product is offered in 1 x Ã-½ in. through 8 x 2 in. sizes. Fully assembled unit, rated at 232...
Read More »
Needle Valves target general utility service.
Offered in stainless and carbon steel, Series GU isolates and vents system media in instrument air, nitrogen header, lube oil, and general utility service applications. Two-piece knuckle joint drives hardened stem tip to create leak-tight seal, while non-rotating stem design minimizes seal wear and protects seat from galling. Available in straight and angle patterns, valves offer choice of end...
Read More »
Circulator-Flange Ball Valve suits hydronic heating systems.
Models 8100 and 8111 feature 2-piece, brass-body, full-port design with free-floating flanges that facilitate alignment with circulator pump flanges. While 8100 has threaded-end and 8111 has soldered ends, both are designed to simplify isolation of circulator pumps for quick testing, repairs, or replacement without need to drain entire system. Sizes of Ã-¾, 1, and 1Ã-¼ in. are rated at...
Read More »
Positive Displacement Pumps suit adhesive applications.
Able to handle wide range of viscosities, Viking pump line offers capacities from milliliters per minute to 1,500 gpm. Internal gear, external gear, and rotary lobe pumps come in variety of materials including stainless steel to address corrosive nature of many adhesives. Jacketed pumps are suited for hot melts, while sealless pumps prevent air infiltration, and dispensing pumps provide precise...
Read More »
5 and 13 Micron Resolve Columns with Greater Bed Stability
Jordi Labs provides materials solutions that set the standard for innovation and quality. Our line of GPC and GFC columns are on the cutting edge of precision manufacturing and a result of our uncompromising commitment to quality and customer service. See our video to learn more.
Read More »
