New Electronic Components & Devices Products

Digital Readouts (DROs) suit machine applications.

Three classes of DROs feature absolute/incremental operation, inch/metric conversion, and linear and segmented error compensation. Also offered: switchable resolutions, radius/diameter readings, zero reset/data preset, self diagnostics, center find, and home reference. Models include A50 (basic model), mid-range C70 and C80, and E70-M and -L models. They hold protection ratings of IP67 (fully...

Racks and Cabinets accommodate network equipment.

EIA 310-D industry standard, 19 in. wall-mount racks and cabinets include 5 models in 18 different configurations. Hinged wall-mount panels, available in 1, 2, 4, 6, or 8 rack units accommodate partial network installations or remote nodes, while fixed wall-mount racks in 12, 20, 25, and 32 rack units are suitable for banks of small networking equipment. Racks and cabinets are constructed of 12...

Cutting Inserts improve efficiency and productivity.

Aluminum Cutting Inserts are available in WCGT 05 and WCGT 06 sizes to mount into existing OTM HOLESHOT(TM) and HOLESHOT(TM)-IS (Integral Shank) drills. Available in grade 12, inserts feature highly polished surfaces and up-sharp geometry for drilling aluminum. Their polished surfaces reduce coefficient of friction for drilling in soft, gummy material.

Surge Protective Devices incorporate diagnostic monitoring.

Panel-mounted Series 75000 and 74000 SPDs are designed for facilities with 3-phase, WYE-configured systems. Units record and download surge events, and provide visual and audio abnormal condition alarms. They have high rating for maximum single-pulse surge current: 200kA for 74000 models, and 320kA for 75000 models. Seven-mode protection covers each phase to neutral, each phase to ground, and...

Deploying Commercial Electronics in Rugged Environments

This white paper explores how Commercial Off-the-Shelf components can be used efficiently and cost-effectively in critical military applications.

Microprocessor Module works in embedded systems.

RCM3000 RabbitCore has Rabbit 300(TM) microprocessor, measures 2.73 x 1.85 in., and operates at 3.3 V. It has 6 serial ports, 10Base-T Ethernet, up to 512K each of Flash and SRAM, quadrature encoder inputs, PWM outputs, and pulse capture and measurement capabilities. Two 34-pin connection headers provide 52 digital I/O shared with 6 serial ports. Programs are developed with Dynamic CÃ-®...

Connectors work in temperatures from -40 to 185 deg F.

Hot Melt ST, SC, and FC fiber optic connectors are approved for indoor and outdoor use as single-mode and multimode connectors. They meet EIA/TIA 568B standards for outdoor applications, and incorporate reheatable adhesive technology and physical contact, pre-radiused zirconia ceramic ferrule technology. Insertion loss values are less than 0.2 dB. Single-mode and multimode units are tested to...

Snap-On Connectors rated for 500 Vrms, -65 to +165 deg C.

Mini-SMB 75 ohm connectors deliver dc to 4 GHz speed for broadband wireless applications. Connectors comply with MIL-STD 348 and meet Mil-c39012 requirements. Series includes straight RSB-200-1-17 and right angle RSB-21-0-1-179, crimp plugs for RG-179/U cable, vertical and right angle PCB plugs and jacks, and straight RSB-220-1-179 and bulkhead RSB-221-1-179 crimp jacks for RG-179-U cable. All...

Connector carries 1.5 amperes for wire harnessing.

Mini MiII(TM) 1.25 mm pitch connector system is available in wire-to-board and wire-to-wire configurations in 2 to 20 circuits for single row and 10 to 40 circuits for dual row. Single row IDT receptacle has guide slots to facilitate wire placement. Side ribs provide polarization and lock into clip for dual-row configurations. Header options include single or dual row, SMT or through-hole, and...

Instrumentation Fittings handle high pressures.

MPI(TM) connectors operate at pressures of 6,000 to 15,000 psi, making them suitable for equipment used to operate feed lines, processing lines, and other systems within industrial labs. Four-part fittings can be used on 316 stainless-steel, cold-drawn, 1/8 hard, unannealed tubing or thick-walled, annealed, instrumentation-grade 316 tubing, and are available for tubing ranging from 1/4 to 1 in....

CompactPCI Bridge expands controller capability.

VMICPCI-5800 single-slot CompactPCI-to-CompactPCI bridge makes it possible for single host controller to access devices in multiple CompactPCI chassis. Bridging requires minimum of two boards; one Master and one Slave. One master can control up to four slaves. Each individual link is 4 wire serial differential connection that provides full-duplex connection at 2.5 Gb/sec. Operating system support...

Custom Fabrication & Machining Services with Over 30 Years of Experience

As a trusted manufacturer to customers across a broad range of industries, Key Gas Components is a premier provider of CNC machining and tube fabrication. Our entire organization is quality driven and customer-centric, with broad-based manufacturing capabilities that can accommodate the most challenging requirements. See our video to learn more.