New T5MV Coaxial Termination with 0.5 Watts Maximum Power
Operating temperature range is -85°C to +125°C and impedance is 50 ±1 Ohm. Measure 0.82 inches in length and 0.36 inches in diameter and connector is 1.85mm male. Designed for radio, antenna and many types of RF components .
Read More »
New T5MV Coaxial Termination with 0.5 Watts Maximum Power
Operating temperature range is -85°C to +125°C and impedance is 50 ±1 Ohm. Measure 0.82 inches in length and 0.36 inches in diameter and connector is 1.85mm male. Designed for radio, antenna and many types of RF components .
Read More »
New TL10/NEX10M/LP Termination Load is Suitable for Small Cell Wireless Applications
Designed to fit in tight spaces for testing or terminating ports on Nokia radio unit head units. Offers 10 W load terminating with NEX10 male connector. Meets Nokia standard ITE-7523 standards and compliant to test radio head or terminating unused ports.
Read More »
New TL10/NEX10M/LP Termination Load is Suitable for Small Cell Wireless Applications
Designed to fit in tight spaces for testing or terminating ports on Nokia radio unit head units. Offers 10 W load terminating with NEX10 male connector. Meets Nokia standard ITE-7523 standards and compliant to test radio head or terminating unused ports.
Read More »
Why Choose a Concept-to-Completion Sheet Metal Fabricator
Concept-to-Completion provides you with the services and guidance you need to get your metal fabrication project done better, faster, and more cost effectively, all in one place.
Read More »
Pasternack's New Quick Connect RF Loads Support Frequency Ranging from DC to 40 GHz
Quick Connect RF Loads from Pasternack are available with QMA, QN, 4.3-10, SMP, SMP-M and BMA connectors. Units offer VSWR as low as 1.1:1 and input power up to 2W maximum and are suitable for applications DAS systems, base stations, antennas and test instrumentation. QMA model is made from tri-metal-plated brass, SMP with gold-plated brass, SMP-M from gold-plated beryllium copper and 4.3-10...
Read More »
Pasternackâ™s New Quick Connect RF Loads Support Frequency Ranging from DC to 40 GHz
Quick Connect RF Loads from Pasternack are available with QMA, QN, 4.3-10, SMP, SMP-M and BMA connectors. Units offer VSWR as low as 1.1:1 and input power up to 2W maximum and are suitable for applications DAS systems, base stations, antennas and test instrumentation. QMA model is made from tri-metal-plated brass, SMP with gold-plated brass, SMP-M from gold-plated beryllium copper and 4.3-10...
Read More »
Ultra Broadband Chip Termination suits microwave applications.
Attleboro, Massachusetts USA – Barry Industries, an ISO9001:2008 certified, ITAR registered manufacturer of high quality thick film resistors, announces the introduction of an ultra-broadband, DC to 60GHz chip termination for microwave applications. The uniquely designed TV0404FA-50R0JN-91 has been third-party tested to show a typical return loss of 18.5dB or better over a DC to 60GHz...
Read More »
Ultra Broadband Chip Termination suits microwave applications.
Attleboro, Massachusetts USA – Barry Industries, an ISO9001:2008 certified, ITAR registered manufacturer of high quality thick film resistors, announces the introduction of an ultra-broadband, DC to 60GHz chip termination for microwave applications. The uniquely designed TV0404FA-50R0JN-91 has been third-party tested to show a typical return loss of 18.5dB or better over a DC to 60GHz...
Read More »
RF Termination (500 W) has DC to 4.5 GHz bandwidth range.
Occupying 1.25 x 1.00 in. footprint, flange mount T50R0-500-15X dissipates 500 W with- return loss of 20 dB or better return loss from DC to 2.5 GHz and 17 dB to 4.5 GHz. This RoHS-compliant thick film on Beryllium Oxide (BeO) termination, which has internally matched circuit architecture, features silver-plated copper flange and input tab. Along with 500W power rating, features include...
Read More »
RF Termination (500 W) has DC to 4.5 GHz bandwidth range.
Occupying 1.25 x 1.00 in. footprint, flange mount T50R0-500-15X dissipates 500 W withÃ- return loss of 20 dB or better return loss from DC to 2.5 GHz and 17 dB to 4.5 GHz. This RoHS-compliant thick film on Beryllium Oxide (BeO) termination, whichÃÂ has internally matched circuit architecture, featuresÃÂ silver-plated copper flange and input tab. Along with 500W power rating,...
Read More »
Precision Machined Parts for High Tech Applications
For precision and value that sets the standard for quality and craftsmanship, EGS Production Machining is the source for precision and value. Our extensive capabilities and dedication to customer service allow us to deliver the optimal manufacturing solution. See our video to learn more.
Read More »
