Electronic Drivers

New LED Backlight Drivers from Kinetic Technologies Enable Manufacturers to Reduce the PCB Area
Electronic Drivers

New LED Backlight Drivers from Kinetic Technologies Enable Manufacturers to Reduce the PCB Area

Kinetic Technologies’ LED Backlight Drivers include KTD3133, KTD3134, KTD3136 and KTD3137 models. The units are available in RoHS compliant 12-ball 1.19 mm x 1.64 mm WLCSP and offer LED backlighting for LCD displays up to 7 in. They provide an input range of 2.7 V~5.5 V and I2C/PWM dual dimming control scheme. These drivers feature programmable current sink, OVP and current limit and selectable...

Read More »
New DM Series Gate Driver Modules Feature Built-In DC-DC Converters and Drive Circuits
Electronic Drivers

New DM Series Gate Driver Modules Feature Built-In DC-DC Converters and Drive Circuits

DM Series Gate Driver Modules are available in four models 2DM150606CM, 2DM150806CM, 2DM180206CM and 2DM180506CM. Units come with AC2500 Vrms dielectric withstand voltage, miller clamp circuit and 5 V logic input. The modules are protected to over current by DESAT detection and offer a response time of 100 ns and parasitic capacitance of 15 pF. Units are used as power conditioners for...

Read More »
The Next Wave of Intelligent Design Automation
Sponsored

The Next Wave of Intelligent Design Automation

In the amount of time it takes to set up a meeting to discuss just one design, engineers can now explore designs exponentially. Generative design has catalyzed a paradigm shift in product development. This shift not only drastically decreases the time it takes to design a product. It also opens the door to design options that might never have been imagined by engineers on their own.

Read More »
New PHB Series LED Programmable Drivers Come with Computer Controlled Dimming Technology
Electronic Drivers

New PHB Series LED Programmable Drivers Come with Computer Controlled Dimming Technology

PHB Series LED Programmable Drivers are offered in 30W/40W/50W models with aluminum housing in side lead, bottom lead or European terminal block configurations. Units come with Tri-Mode Dimming™ compatibility with 0-10V, TRIAC and ELV dimmers and 5 pre-programmed dimming options. The drivers deliver programmable 1% TRIAC dimming granularity and an efficiency of 90% from 50-100% of load with...

Read More »
New LD15CHA Laser Diode Drivers are Suitable for Laser Cutting and Laser Diode Bar/Stack Applications
Electronic Drivers

New LD15CHA Laser Diode Drivers are Suitable for Laser Cutting and Laser Diode Bar/Stack Applications

LD15CHA Laser Diode Drivers from Wavelength Electronics deliver an output of 15 A current up to 28 V voltage. Units feature a bandwidth of 600 kHz, stability of less than 200 ppm (CC) and 0.3% (CP) with RMS Noise current of 35 μA at 100 kHz. Available in models with output of 2.5 A, 5 A, and 10 A, diodes come with 100 nA/√Hz noise current density, over-/under-voltage protection and slow-start...

Read More »
IX4340UE low-cost Dual 5A Gate Driver IC presents operating temperature range of -40°C to +125°C.
Electronic Drivers

IX4340UE low-cost Dual 5A Gate Driver IC presents operating temperature range of -40°C to +125°C.

Featuring two high current outputs, both capable of sourcing and sinking up to 5A, IX4340UE comes with logic inputs that are TTL and CMOS logic compatible. With both outputs having an absolute maximum voltage rating of 20V, device offers matched propagation delays, and identical output drivers that can be connected in parallel for higher current applications. Suitable for high frequency...

Read More »
LNP-C Series LED Drivers deliver an efficiency of up to 90.5%.
Electronic Drivers

LNP-C Series LED Drivers deliver an efficiency of up to 90.5%.

LNP-C Series of LED Drivers are compatible with COB and mid-power LEDs. Units are operated on 198-264Vac input voltage and offer fixed current output with power ranging from 11W to 40W. Product is suitable for commercial and residential lighting and are manufactured to IEC/EN 61347-1, IEC/EN 61347-2-13 and EN 62384 standards. Units come in independent type housing designs for stand-alone...

Read More »
Isolated Gate Drivers offer CMTI performance of >150 kV/μs.
Electronic Drivers

Isolated Gate Drivers offer CMTI performance of >150 kV/μs.

Available in ADuM4120, ADuM4120-1, ADuM4121 and ADuM4121-1 models, Isolated Gate Drivers are suitable for solar inverters, motor controllers and industrial inverter applications. ADuM4120 model features input glitch filter, while ADuM4120-1 model without glitch filter offers typical propagation delay of 33ns. ADuM4121 and ADuM4121-1 models are designed with internal Miller clamp. Operated with...

Read More »
LNE-320W Series of LED Drivers meet IP65/IP67 standards.
Electronic Drivers

LNE-320W Series of LED Drivers meet IP65/IP67 standards.

Available in 12 V, 24 V, 36 V and 48 V output voltages, LNE-320W Series of LED Drivers are housed in corrosion resistant aluminum casing. Unit comes with adjustable output voltage, current levels and LED brightness with 3-way built-in dimming options. Offering more than 700,000 hrs of MTBF, units meet IEC/EN 61000-3-2, Class C standards. Drivers come with 6kV and 4kV of common mode and...

Read More »
How SpinSelect Can Save You Time and Money
Sponsored

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.

Read More »

All Topics