Active Harmonic Filters improve power quality.
Comprised of scalable, 3- and 4-wire active harmonic filter modules/systems,Â- Power Balance & Kxxx Series meet IEEE-519 and Mil-Std-1399 with respective values of 5% TDD and
Read More »Analog Modules target engineers and instructors.
RLC Divider Board was developed to implement passive filters and various R, L, and C networks, whileÂ- Level Shifter Board is designed to interface I2C or SMBus signals between devices with different VDD voltages. Using OPA172 operational amplifier, OpAmp Board includes specific features that make it suitable for experimentation. Active Filter Board is suited for use as anti-aliasing filter...
Read More »
Harmonic Filters include 600 and 690 V variants.
Operating at over 99% efficiency, Matrix® AP harmonic filters include 600 V, 60 Hz and 690 V, 50 Hz models that help designs meet IEEE-519 requirements for harmonic distortion regardless of power load. These UL and cUL Listed products employ Adaptive Passive technology and adapt impedance in response to changing electrical loads. AvailableÂ- with 6–786 A...
Read More »Modular Passive Harmonic Filters come in high power versions.
Available as open frame modules, ECOsine® filters enable high-power AC or DC motor drives to be upgraded toÂ- low harmonic drive. Chokes module is designed for placement at bottom of cabinet, while capacitor and RC-damper modules can be placed wherever space is available. While FN3410 filters for 380–500 V, 50 Hz grids are available with standard ratings from 200–400 kW, FN3412...
Read More »
Rack System Design & Buyer's Guide
There is plenty to consider before setting up or replacing storage rack systems in your warehouse. This whitepaper contains a guide and general checklist of the most important considerations.
Read More »
Wall-Mounted Active Harmonic Filters incorporate PFC.
Comprising 3- and 4-wire active (3 x 200 Vac to 3 x 480 Vac) harmonic filter modular systems, wall-mount Power Balance (PB-W) Series monitors current signal and compensates for unwanted elements of measured current. Scalable solutions, designed to meet IEEE-519, eliminate harmonic oscillations to improve power quality. Features include 21 Â-µsec reactive power compensation, phase...
Read More »Active Harmonic Filter supplies up to 960 A correcting current.
Supplied in wall mount configuration, 480 V Matrix PureSine® Active Harmonic Filter is used for coordinated variable load PFC, phase imbalance, and harmonic mitigation. Modular unit operates up to 51st harmonic with up to 12 harmonic orders selected individually. Supporting parallel operation, device features full-time DSP control system, shunt connection to facilitate maintenance, and LCD...
Read More »
Power Filters are offered in DIN rail-mount versions.
DTRF family of 3-phase filters without neutral are available for currents of 20, 30, and 50 A. Terminal system ensures fast and reliable electrical connection, while plastic housings and lack of internal resins make filters lightweight. Typical applications include electro-medical equipment, frequency inverters, servo drives, and switching power supplies. Filters are designed according to UL1283...
Read More »Digital Active Harmonics Filters perform targeted PFC.
In addition to providing real-time mitigation of harmonic currents up to 50th order, ECOsine Active Filters immediately compensate for voltage dips and reactive power surges. Units continuously measure and analyze disturbances in power network and provide exactly opposite compensation current, responding in less than Â-½ ms. Filters are available in 3-phase/3-wire as well as 3-phase/4-wire...
Read More »Filters/ADC Drivers suit I/Q demodulator channel filtering.
Broadband active filters/ADC driver amplifiers include LTC6603, LTC6601-1, LTC6605-7, LTC6605-10, and LTC6605-14. Model LTC6603 features dual matched programmable ninth-order switched capacitor linear-phase filter and ADC driver, where as LTC6601-1, is low noise 0.5% tolerance lowpass active filter and ADC driver with configurable bandwidth from 5-28 MHz. LTC6605-7/-10/-14, are second-order...
Read More »
Three-Phase Filters enable assembly on DIN rail.
Designed according to UL1283 and EN60939 regulations, DTRF series filters three-phase without neutral for currents of 20, 30, and 50 A. They feature plastic housings, no internal resins, and low leakage current. Compact filters suit applications including automation machinery, electro-medical equipment, frequency inverters and servo drives (with short length cables), switching power supplies, as...
Read More »
Dies & Stamping Services with Over 25 Years of Experience
PDS is an established leader in progressive die stamping, with a reputation for providing precision and value that dates back more than half a century. Through extensive capabilities and a staff of seasoned professionals, we set the standard for quality, delivering flexible services that can meet the needs of the most challenging requirements. See our video to learn more.
Read More »
