New Electronic Components & Devices Products

Filter never needs to go off-line for backwashing.

CYCLOSPRAY(R) Filter's internal cleaning shower continuously removes captured particulate matter from filter media. Continuous cleaning allows CYCLOSPRAY(R) to handle solids up to 5000 ppm. At larger mesh sizes, CYCLOSPRAY(R) can handle flow rates of up to 300 gpm. Positive filtration device provides absolute barrier against suspended solids and is available with mesh sizes as small as 1 micron.

Serial I/O Adapter fits CompactPCI-based computers.

ISO COMM2.cPCI multi-interface I/O adapter provides two individually selectable RS-232/422/485 isolated serial ports that support data rates up to 921.6 Kbps. True port to port optical isolation eliminates effects of ground loop current. It isolates not only signals, but also isolates ports from each other. Auto-enable hardware automatically handles RS-485 driver, allowing RS-485 ports to be...

LED Driver can power three at a time.

S-8813 Series three-channel white LED driver IC can power up to 3 LEDs. S-881300OBPE-TB allows user to vary output current linearly between 5 and 18 mA by changing voltage supplied to current set pin (VISET). S-881300CPE-TB allows user to set output current between 5 and 18 mA by connecting resistor to current set pin (RISET). Ultra-small SON10 package and constant-current output make series...

Connector eliminates bent pins.

Power-Edge(TM) PEC Series has edge card interface with 3, 7 or 10 contacts. One-piece interface is rated up to 5 A and has contacts on .100 in. pitch. Built-in card latches increase withdrawal force required for removing power board. Optional alignment pins and locking clips can be provided.

Access Hardware: Medical Solutions

This guide will provide a closer look at solutions for medical equipment and devices

Microwave Preamp covers wide bandwidth.

LN1G11 Low Noise preamp covers bandwidth of 1.0 to 11.0 GHz, has minimum gain of 27dB, and is suitable for amplifying low-level signals to drive power amplifiers. With its low noise, it can also be used to increase sensitivity of EMC receivers that have relatively high noise figures. It comes with benchtop cabinet and front or rear connectors. Other preamplifiers are available with frequencies...

Heavy Duty Contactor fits group lighting applications.

Meter based DURALOAD(TM) provides standard two pole, 100 A per pole control of group lighting. It has NEMA 3R rugged lightweight enclosure and field re-settable circuit breakers. Access below front control panel allows for easy field measurement of load current and voltage. SCADA options for control and monitoring are available.

RF Inductors withstand shear test to 4.4 lbs.

SMRF 1812 surface mount inductors provide inductance values from 1.0 to 1000 microHenries and current ratings from 450 to 30 mA. They exhibit resistance to thermal shock, and resist soldering temperatures up to 250 deg C for 30 seconds. Applications for SMRF 1812 inductors include RF signal circuitry in communications, test & measurement, medical diagnostic, and industrial process control...

Interface connects to any PLC.

QuickBloc Universal PLC interface has 8 or 16 channels, connects to any manufacturer's PLC, and has choice of screw or tension clamp technology. It comes with terminals, pre-wired cable with flying leads ready to attach to any PLC's front panel adapter, and pre-printed marking tags. Options are available for fusing, analog signals, and PCB versions that use pluggable cable system.

Signal Conditioners handle hundreds of I/O combinations.

WAVEANALOG is available in three models, all providing 0 to 10 Vdc, 0 to 20 mA, or 4 to 20 mA output signals. Pro DC-DC takes inputs between 20 mV to 200 Vac bipolar for voltage and 0.1 to 100 mA bipolar for current. Pro RTD field configurable signal conditioner takes PT100/2/3/4-wire RTDs, Ni 100, and potentiometer inputs. Pro Thermo takes thermocouple types K, J, T, E, N, R, S, and B inputs....

Air To Electronic Converter displays air gage signals.

Compact VE-03 mounts as free-standing unit to standard DIN rail. In operation, air input signal is received in front of converter through air adapter. Output signal is transferred to electronic column or gage computer from signal output socket at back of unit. Zero and gain controls on front of converter adjust electric signal. Zero control is used for adjusting zero point on electronic column...

Optimize Your Storage or Distribution Facility with Steel King Rack Solutions

Steel King racks are designed to meet seismic requirements in the most demanding conditions. Our durable storage products help your company save on maintenance costs. Check out our product video or download our Rack Planning eBook to learn more.