Lead Assemblies handle high voltages.
Hi/Mate 12 gauge contact lead assemblies for MIL-C-38999 Series I, III, and IV connectors withstand up to 13.5 kVdc, commonly found in densely packaged, high-voltage power supplies, CRTs, and TWTs. Assemblies are terminated with Hi Voltage FEP cables. Insertion and removal procedures use same tools as standard 38999 connector. Lead assemblies are electrically isolated from connector shell and can...
Read More »Transmitters convert analog input signals to digital data .
DIN-100 Sensor to Computer Modules transmit data via RS-485 to controller, which may be computer or other processor-based equipment. Modules measure temperature, pressure, voltage, current, digital input, or digital output signals. They perform all signal conditioning, scaling, linearization, and conversion to linearized ASCII data values or Modbus RTU data values. Address, baud rate, parity, and...
Read More »
Analog Output Modules plug into PCI port.
With 16-bit NI PCI-6731 and NI PCI-6733 analog output modules, engineers can control waveform amplitudes with higher resolution. Both modules deliver high-channel density, 1 MS/s per channel 16-bit analog waveform output, and two counter/timers. NI PCI-6731 has four output channels, and NI PCI-6733 has eight. Both come with NI-DAQ 6.9 driver software that works with NI LabVIEW, LabWindows/CVI,...
Read More »
D-Sub Connnectors plug into Profibus.
SUBCON-PLUS field-wire connectors make wiring and installation of Profibus nodes easy by providing a way to make terminations without soldering or crimping. Incoming and outgoing bus lines connect to screw or spring clamp terminal blocks. Connectors have EMI/RFI shielded housing, making it suitable for use on cables with up to 12 Mbit/s data rates. Available with angled or straight cable feeds....
Read More »
The Use of Water Treatment in the Healthcare Industry
Facilities Where Water Treatment for Healthcare Is Essential
Read More »
Distribution Blocks come with spring cage terminals.
FLKM-PVB power distribution modules are available in 16, 24, 32, and 48 positions, all with spring cage terminals. Each module is equipped with two potential connections: P1 and P2. Each supply terminal is capable of accepting up to 10-gauge conductor, and each distribution terminal is capable of accepting up to a 12-gauge conductor. There are no external bridging connections to be made on this...
Read More »
Interface Boards connect to Galil motion controls.
VARIOFACE interconnect for Galil OPTIMA and ECONO series digital motion controllers can be used directly with Galil's 100, 80, and 36-pin cables. The 100-pin version comes with additional amplifier driver circuit and discrete screw connection to all conductors of Galil cable. Specific marking of each connection allows for quick, space-saving installation. Module is available as DIN-Rail or...
Read More »
Industrial Ethernet Connectors meet IP67 watertight rating.
Variosub RJ-45 connectors are suitable for fast Ethernet transmissions at 100 Mbps in accordance with Class D or Category 5 of EN 50173. Protects against dirt and moisture, withstands adverse conditions associated with use on machinery and industrial installations, and protects RJ-45 contact insert. Connector is protected against forces pulling mounting and hood sides apart, pulling cables out of...
Read More »
Connector facilitates torch changing.
Advanced Technology Connector(ATC)(TM) makes it possible for end users to adapt SureLok(R) cutting torches to various manufacturer's air plasma cutting systems. Torch with connector is available with outputs up to 100 A and allows user to connect or disconnect with less than one thread-turn. Connector is less than 2 in. in dia. Lead extensions are available for additional flexibility.
Read More »Laboratory Mixers offer brushless DC motors.
D & A Mag-Drive(TM) Sealed-Vessel Mixers are available in 3 models. Their bodies seal vessel for pressure/vacuum operation or containment of hazardous materials in laboratory glassware. Magnetically coupled bench-scale mixers cannot de-couple. They offer in-line design, drop-in seal, and manually-adjustable, variable speed up to 2250 RPM.
Read More »
Surge Suppressor handles three phase power.
BRICKTRAB modular DIN-rail mountable transient voltage surge suppressor provides power installations with more than 40,000 A of surge current handling capacity and low voltage protection levels. It protects against normal mode (line-to-line) and common mode (line-to-ground) transients, and has diagnostic monitoring of protection status with local and remote failure indication. Meets UL 1449 2nd...
Read More »
Standex Engraving Mold-Tech Offers Nickel Shell Capabilities on a Global Scale
Standex Engraving Mold-Tech is the premier, global supplier for mold texturing and surface finishing. With a full range of services, Standex Engraving Mold-Tech is also the only nickel shell supplier producing in three global locations. See our video to learn more.
Read More »
