Fasteners & Hardware

Clip is designed to route cables in corners.
Clips

Clip is designed to route cables in corners.

Kwik Corner Klip KKK-4-RT makes 90 deg angle between back and base of clip, making it suitable for routing cables into corners. Clip is extruded from PVC material and can be mounted with acrylic double backed adhesive tape provided on base. It can be provided in any specified length.

Read More »
Latches

Compression Latch keeps out contaminants.

Folding T-handle latch provides 6.4 mm of pull-up compression eliminating shock and vibration and providing tight seal against outside contaminants. Handle also compresses gaskets to eliminate vibration and reduce noise levels, helping equipment manufacturers comply with international standards relating to noise emissions. It is available in two styles: with mounting cup for flush surface, and...

Read More »
Narrow Pincer fits into confined areas.
Clamps

Narrow Pincer fits into confined areas.

For applying and removing stainless steel clamps, Narrow Jaw Pincer is only 3/8 in. wide, allowing it to fit into tight areas. It is made of forged steel with plastic-covered handles that make gripping easy. Smooth, rotating action of pincer's handles allows tool to operate easily. Applications include retrofit or repair operations, where equipment, appliances, and machinery is constructed with...

Read More »
Wing Nuts resist solvents, oils and grease.
Nuts

Wing Nuts resist solvents, oils and grease.

Ergostyle wing nuts and wing screws are made from glass-fiber reinforced technopolymer plastic with black matte finish. Brass-tapped insert on wing nut is molded in, while wing screw's threaded stud is steel and zinc-plated. Metric versions in brass or stainless steel of each are available. Concave marks on ends of wings help position fingers so maximum force can be applied. Cover caps in orange,...

Read More »
One-Handed Clamp uses self-restraining technology..
Clamps

One-Handed Clamp uses self-restraining technology..

Adelok® helps assemble clamped components by holding itself closed and in place during installation. It is suitable for rapid clamp assembly and improved stacking methods for fluid lines and hoses, wire bundles, power cables and fire detection sense lines. Juggling of fasteners, standoffs, washers, ties and grommets is eliminated. Clamp can handle payloads of 0.062 to 3.50 in., and can be...

Read More »
Quick Release Pins require no tools.
Self-Locking Pins

Quick Release Pins require no tools.

Sky-Loc Rapid Release positive locking pins will not release until button on handle is depressed so balls retract into pin. Because pins can be removed without tools, they are ideal for quick change-over applications and field work. Pins are available in 17-4 and 304 stainless steel for commercial and industrial applications, respectively. All pins are stocked in four handle configurations with...

Read More »
Roof Fastening System gets FM and Sarnafil approvals.
Fastening Systems

Roof Fastening System gets FM and Sarnafil approvals.

Isofast automated fastening system has obtained Factory Mutual and Sarnafil approval for enhanced wind uplift protection on Sarnafil S327 roof membranes. It uses IF160 setting machine and belted XPS fasteners and plates to secure Sarnafil S327 PVC membranes. Fasteners are #15, self-drilling units that exceed FM premium corrosion standards, while rectangular plates are barbed, 20-gauge galvanized...

Read More »
Inserts

Milling Cutters work fast and efficiently.

Fix-Perfect aluminum milling cutter inserts have on-edge orientation and 34 deg positive rake angle. This geometry reduces insert edge buildup, improves tool life, and provides free cutting action that makes it possible to machine thin-walled parts. Inserts are available in uncoated, coated, and polycrystalline diamond versions.

Read More »
Precision Core Pins are for luer taper applications.
Pins

Precision Core Pins are for luer taper applications.

Rosspunch pins are precision ground for injection molding of plastic luer taper components. Pins are custom made with tolerances to 0.0005 in. length and 0.0001 in. dia. in steps from 0.006 to 0.750 in. They can be made from all common tool and stainless steels in 0.250 to 10 in. lengths. Pins can incorporate ground ends with radii, flats, symbols and odd shapes. They can also be nitrided, TiN...

Read More »
Mold Dating Insert snaps in place.
Inserts

Mold Dating Insert snaps in place.

Indexable mold dating insert allows molders to make fast changes to day, month, year or work shift without completely removing insert from mold. Date changes can be made with turn of screwdriver, while snap-in-place indexable adjustment ensures insert remains fixed in correct date position during production. Mold dating inserts are available in diameters of 6, 8, 10, 12, 16 and 20mm. Inserts are...

Read More »
Precision Machining Solutions with Over 25 Years of Experience
Sponsored

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.

Read More »

All Topics