Fasteners & Hardware

Locking Key Slot attaches standoffs and fasteners to PCB.
Studs

Locking Key Slot attaches standoffs and fasteners to PCB.

LKS can be used in place of pressed in metal screw insert to attach fasteners to circuit boards and panels. It is easily installed and removed by hand from same side of panel. It has low insertion force yet pullout force exceeds strength of most standard PC boards. Slot is made of Nylon 6/6 to fit panels and circuit boards 0.062 in. thick. LKS holds standoffs, wire ties, wire routing clips and...

Read More »
Clip is designed to route cables in corners.
Clips

Clip is designed to route cables in corners.

Kwik Corner Klip KKK-4-RT makes 90 deg angle between back and base of clip, making it suitable for routing cables into corners. Clip is extruded from PVC material and can be mounted with acrylic double backed adhesive tape provided on base. It can be provided in any specified length.

Read More »
Latches

Compression Latch keeps out contaminants.

Folding T-handle latch provides 6.4 mm of pull-up compression eliminating shock and vibration and providing tight seal against outside contaminants. Handle also compresses gaskets to eliminate vibration and reduce noise levels, helping equipment manufacturers comply with international standards relating to noise emissions. It is available in two styles: with mounting cup for flush surface, and...

Read More »
Narrow Pincer fits into confined areas.
Clamps

Narrow Pincer fits into confined areas.

For applying and removing stainless steel clamps, Narrow Jaw Pincer is only 3/8 in. wide, allowing it to fit into tight areas. It is made of forged steel with plastic-covered handles that make gripping easy. Smooth, rotating action of pincer's handles allows tool to operate easily. Applications include retrofit or repair operations, where equipment, appliances, and machinery is constructed with...

Read More »
Wing Nuts resist solvents, oils and grease.
Nuts

Wing Nuts resist solvents, oils and grease.

Ergostyle wing nuts and wing screws are made from glass-fiber reinforced technopolymer plastic with black matte finish. Brass-tapped insert on wing nut is molded in, while wing screw's threaded stud is steel and zinc-plated. Metric versions in brass or stainless steel of each are available. Concave marks on ends of wings help position fingers so maximum force can be applied. Cover caps in orange,...

Read More »
One-Handed Clamp uses self-restraining technology..
Clamps

One-Handed Clamp uses self-restraining technology..

Adelok® helps assemble clamped components by holding itself closed and in place during installation. It is suitable for rapid clamp assembly and improved stacking methods for fluid lines and hoses, wire bundles, power cables and fire detection sense lines. Juggling of fasteners, standoffs, washers, ties and grommets is eliminated. Clamp can handle payloads of 0.062 to 3.50 in., and can be...

Read More »
Quick Release Pins require no tools.
Self-Locking Pins

Quick Release Pins require no tools.

Sky-Loc Rapid Release positive locking pins will not release until button on handle is depressed so balls retract into pin. Because pins can be removed without tools, they are ideal for quick change-over applications and field work. Pins are available in 17-4 and 304 stainless steel for commercial and industrial applications, respectively. All pins are stocked in four handle configurations with...

Read More »
Roof Fastening System gets FM and Sarnafil approvals.
Fastening Systems

Roof Fastening System gets FM and Sarnafil approvals.

Isofast automated fastening system has obtained Factory Mutual and Sarnafil approval for enhanced wind uplift protection on Sarnafil S327 roof membranes. It uses IF160 setting machine and belted XPS fasteners and plates to secure Sarnafil S327 PVC membranes. Fasteners are #15, self-drilling units that exceed FM premium corrosion standards, while rectangular plates are barbed, 20-gauge galvanized...

Read More »
Inserts

Milling Cutters work fast and efficiently.

Fix-Perfect aluminum milling cutter inserts have on-edge orientation and 34 deg positive rake angle. This geometry reduces insert edge buildup, improves tool life, and provides free cutting action that makes it possible to machine thin-walled parts. Inserts are available in uncoated, coated, and polycrystalline diamond versions.

Read More »
Precision Core Pins are for luer taper applications.
Pins

Precision Core Pins are for luer taper applications.

Rosspunch pins are precision ground for injection molding of plastic luer taper components. Pins are custom made with tolerances to 0.0005 in. length and 0.0001 in. dia. in steps from 0.006 to 0.750 in. They can be made from all common tool and stainless steels in 0.250 to 10 in. lengths. Pins can incorporate ground ends with radii, flats, symbols and odd shapes. They can also be nitrided, TiN...

Read More »

All Topics