New Electronic Components & Devices Products

Test and Burn-In Socket suits applications under 1 GHz.

Designed for use with devices from 14-27 mmÃ-², CSP/MicroBGA pressure-mounted socket requires no soldering and incorporates spring probe contacts, integral plastic alignment posts, and 4-point crown that ensures scrub on solder oxides. Signal path during test is 0.077 in. and operating temperature is -67 to +302Ã-

Audio Amplifier suits portable, wireless applications.

Model TPA6211A1 Mono Class-AB Amplifier offers over 340 mW of power per mmÃ-² and can deliver 3.1 W of power into 3 ohm load at 10% total harmonic distortion. Device comes in 3 x 3 mm QFN package and 3 x 5 mm MSOP package. Typical applications include cell phones, smart phones, and PDAs.

Sources and Amplifiers suit laboratory applications.

Leveraging diode-pumped erbium doped fiber technology, Broadband ASE (amplified spontaneous emission) sources and EDFAs (erbium doped fiber amplifiers) are packaged for test and measurement of photonics components in 1550 nm spectral region. Self-contained BBS-410 and BBS-430 sources generate broadband output as high as 25 mW. Fully-integrated FPA-410 and FPA-415 EDFAs feature signal gains of...

Insulated Gate Bipolar Transistors suit UPS applications.

Rated from 16-60 A as discrete IGBTs or co-packs with internal fast recovery diode, C2-Class IGBTs have negative temperature dependence on saturation voltage. They are suited for off-line power conversion applications requiring 600 V devices with switching frequencies up to 200 kHz. Packaging options include TO-220, surface-mountable TO-263 and TO-268, TO-247, and PLUS247. Products are also...

Design & Manufacturing Process of a Coil

Because the design and manufacturing of electromagnets are critical to the successful operation of the application, it's important to spend time defining your requirements before purchasing coils for an application. This eBook will guide you through the process of evaluating the application's constraints, identifying the needed specifications, and collaborating with a manufacturer to develop an appropriate coil solution for the application.

Bi-Level Edgecard Connector suits heavy-duty applications.

Made of high-density dielectric material, bi-level series right angle edgecard connectors withstand temperatures from -65 to +150Ã-

Shielded Connector System provides EMU suppression.

Q2(TM) shielded connector system incorporates shield plates along sides of connector and terminates them to PCB via selected signal pins. Available in single ended and differential pair versions, system has signal pins on .025 in. pitch and is available with 52, 104, 156, and 208 total pins per connector set. Connectors are polarized to ensure proper mating. In addition to vertical mating,...

LED Products produce 74 lumens per watt.

XThin(TM) solid-state LED emitters combine Group III nitride materials with silicon carbide substrate. Vertically structured LED chips measure approximately 115 microns high and incorporate epi-down design for maximized light extraction efficiency and white light conversion. Applications include next generation mobile appliances' LCD backlights and digital camera flash.

Strain Relief Clamp prevents twisting/flexing problems.

SR-Series Clamp Attachment fits onto back end of RF coaxial connectors to reinforce cable assemblies subjected to excessive twisting and flexing. Product features rolling clamp nut design that provides axial and rotational support and prevents distortion of cable caused by over-tightening. Suited for cables from Ã-¼-Ã-¾ in. OD, product is fully compatible with RG214, RG393, and RG217...

Crystals/Oscillators support TI 1394b FireWire-® devices.

Crystals and Oscillators operate at frequency of 49.152 MHz to meet Texas Instrument's specifications for use with TSB41BA3 Chipset, which is geared toward Long Haul or Long Range applications. A 98.304 MHz, 1.8 V oscillator with critical start-up feature is available for TSB81BA3 Chipset designed for 1394b FireWireÃ-® 800. All products are offered in 5 x 7 mm SMD package specified for 0 to...

Connectors designed for in-field wiring repairs.

Quick-disconnect, picofast M8 Insulation Avoidance Connectors include 3- and 4-pin units that handle 22-26 AWG conductors and are rated for 4.0 A at 60 Vac/75 Vdc. Male or female configurations are available with cage clamp strain relief that provides IP 68 seal. Connectors require no soldering and can be installed almost anywhere. Contact holders are color coded to match standard conductor...

Optimize Your Storage or Distribution Facility with Steel King Rack Solutions

Steel King racks are designed to meet seismic requirements in the most demanding conditions. Our durable storage products help your company save on maintenance costs. Check out our product video or download our Rack Planning eBook to learn more.