New Electronic Components & Devices Products

Filters are available with optional large-tube body.

AFR Series design replaces multiple valves found in systems with single rotating diverter. Actuator design provides more power and torque than original AFR, and is rated for more rotations. Optional 6 in. tubes enable unit to address filtration at low retentions and high flows. They are suitable for flow capacity at low, flow-restricting retentions of less than 100 microns.

Filter Dryer produces dry cakes.

RT(R) filter can be used with either hot-gas drying or infrared drying. Filter is available in open, fume tight, gas tight, and pressure tight configurations, and with full sanitary configuration to meet cGMP requirements. For hot-gas drying, segmented tray design makes it easy to use specific tray sections as hot gas drying zones. Hot gas can be air, nitrogen, or steam. Infrared drying can be...

High-Power Magnifiers sit on desktop or light table.

Compact Clear Base Magnifiers, with magnifying powers of 9x, 12x, and 20x, have achromatic color-corrected lens which provides distortion free viewing and sharp image over entire field of view of lens. Adjustable lens-focusing collar adjusts focus for individual's vision or to view object that is not flat. Magnifiers may be used hands free. Clear base enables work surface to be viewed through...

LED Lamps replace incandescent 194 and 168 bulbs.

Sunlight-visible, right-angled 9 mm (T3-1/4) AUT194 WedgeLED Lamps feature either 4 Super Red (630nm) or Super Yellow (590nm) discrete SML1209-OER-TR or SML1209OPY-TR SMT LEDs, respectively. Discrete LEDs are mounted on printed circuit board integrated into 9 mm wedge base, which are plug-compatible with automotive manufacturers' 12/14-Volt DC systems. Red and yellow AUT-194 LED lamps output 5000...

Hot Forging Process

Check out this white paper to learn about the benefits of hot forging.

LED is visible in direct sunlight.

High-Energy White, water-clear, 8000 K, 3 mm (T1) LED integrates Silicon Carbide/Gallium Nitride (SiC/GaN) diode with optical grade epoxy to produce 3500 mcd illumination at 20 mA. It offers 22 deg viewing angle and sturdy leads for reliability in wire-wrap/through-hole PCB applications. Its solid-state design renders LED imperious to electrical and mechanical shock, vibration, frequent...

Interfaces offer high retention contacts.

Micro-Rugged Interfaces have shrouded and keyed insulators, and PCB terminations including press fit, solder locks, and mechanical hold-down options. Board-to-board interfaces are available on .050 in., 2 mm, and .100 in. pitch. Micro Card interfaces for .031 and .062 in. boards have terminations on .8 mm and 1 mm pitch. Standard and high speed IDC cable systems are available on .050 in., 2 mm,...

Power-Supply Accessory Kit is packaged in blister-pack case.

Model TLPS provides fully insulated alligator clips, standard alligator clips, and spade lug adapters. Retractile, sheathed banana plug connects to power supply, and fixed, sheathed banana plug protect users. Kit includes ready-made, silicone-jacketed, test-lead set for power supplies with remote sensing capabilities. Items meet IEC61010-032 international safety specifications to 1,000 V.

Signal-Conditioner Module offers dual channels.

Test Friendly(TM) Dynamics Model 4120 provides 40kHz signal amplification, non-linearity correction, and cold-junction compensation for conversion of millivolt output of thermocouple into 0 to 10 V signal, linearly proportional to temperature. Programmable voltage reference is provided for internal self test and automated user calibration functions. Each channel can be configured for use with any...

Frame Grabber has half-height, PCI-compatible form factor.

PicPort-Color acquires images from S-Video and Composite video sources in NTSC/RS170/PAL/CCIR/SECAM or PAL-M formats. Onboard electronics insure conservation of color information during digitalization process. LV-SDS Software Suite includes Orchid library, with ActiveX/OCX and regular function calls, Daisy C/C++ core library, Daisy Real-time Application Library, Video for Windows driver, Twain...

Holding Assemblies are offered in hundreds of shapes and sizes.

Permanent Magnetic Holding Assemblies are designed for positioning, stabilizing, holding, and feeding materials, parts, and scrap. Standard configurations and sizes include Ceramic, Alnico, and Rare Earth magnets. Watertight and high-temperature units are available. Assemblies are used in metal product manufacturing, including workholding and spot-welding.

Fresh Air Intake Designed to Meet ASHRAE 62.2 standards

Alan Manufacturing has a long history of developing innovative solutions for HVAC applications. With over 1,000 product designs under our belt, we have gained a reputation as the go-to source for HVAC dampers, hardware, duct supports, zone control systems, and much more. Adding to this extensive list of achievements we now announce the release of our new line of Fresh Air Intake products. Designed to meet ASHRAE 62.2 standards, they are the most robust and high-performance product of their kind. See our video to learn more.