Surge Protection Hub provides single-point grounding.
Employing Sure/Fire Four-Port Building Block as basic element in surge protection design, additional blocks or hubs may be stacked vertically and horizontally for virtually unlimited number of surge protected devices. Faceplates may be color coded to define type of phone line, data interface, LAN, or I/O signal connection attached. Sure/Fire comes with RJ45, terminal block, DB9, DB25, and various...
Read More »
Front End/Rectifier provides power density of 19 W/cu in.
Intended for low-profile, distributed power architecture applications, universal-input, 1,200 W CAR1248 comes in 1.65 x 3.44 x 11.2 in. package with integrated redundant diodes and thermally controlled fan. It delivers 48 V single output at 25 A and is capable of supplying up to 4,800 W N+1 redundant or 6,000 W. Features include hot-swap and fault redundancy, active single-wire load sharing,...
Read More »PC Scope Adapter offers 1 Mb buffer memory.
USB-bus powered, PicoScope 3206 features 200 MHz analog bandwidth and single-shot, 8-bit sampling rate of 200 MS/s. Using Equivalent Time Sampling for repetitive signals, sampling rate is increased to 10 GS/s. Waveform storage is limited only by PC's storage capability. Once captured, PicoScope software allows user to zoom-in on signal at up to 2,000x magnification. Built-in signal generator can...
Read More »
Toroidal Inductors suit power applications.
Thru-hole Series 083AT features inductance from 10-100 Ã-µH and current ratings up to 30 Adc. High current/power capacity units are targeted for use in power supply filtering and energy storage applications. Specific applications include medical diagnostic, monitoring and analysis equipment, electrical/electronic test and measurement equipment, and commercial and industrial control systems.
Read More »
Everything You Need to Know About E-Textiles
This ebook provides an in-depth overview into everything you need to know about E-Textiles.
Read More »
Embedded Module features Intel i815E chipset.
Model ETX-P3T provides complete PC functionality in component that plugs into application-specific carrier board. Power management is achieved using ACPI and APM 1.2, allowing fanless cooling. Module supports Intel 82815 chipset with integrated Graphics Core, 2 IDE ports with support for ATA 33, 4 USB 2.0 ports, up to 512 Mbytes SDRAM, 10/100 Mbit Base-T Ethernet, LVDS up to SXGA 1,280 x 1,024,...
Read More »
Dial Automated Swage Cell offers modular flexibility.
With max cycle time of 6 sec, Dial Automated Swage Cell performs deflashing, gauging, testing, and sizing operations on vibration control bushings. Cell, requiring 80 ftÃ-² of floor space, is assembled in modular arrangement and comprised of sub-assemblies. Dual dial, precision-synchronized indexing tables transfer bushings from station to station, and standard bushing size ranges from 1 in....
Read More »
Laser Diode Drivers provide complete system management.
LYDYA(TM) Q-CW and CW laser diode drivers are for single diodes, bars, and stacks, and are available with or without TE temperature controller. Computer controllable devices include diode shunt that remains plugged to diode terminals and short-circuits when diode is not used, output stage designed to avoid transients, and high power circuitry that supplies regulated adjustable current and...
Read More »
Wirewound Chip Inductors protect electronic circuitry.
Surface-mount, Series DR354-1-2-3-4 provides protection against EMI problems in high-frequency filtering applications. Depending on model, units feature inductance from 1.6-4,700 nH, with DCR from 0.030-4.3 ohms, over max current rating of 0.700-0.230 A. Available in packages as small as 0.044 x 0.071 in. with 0.040 in. profile above circuit board, miniature inductors are suited for appliances,...
Read More »
Linearity Coils are suited for CRT applications.
Printed circuit mount linearity coils SDL-3006 through SDL-3009 are electronically adjustable via control winding that is biased with positive or negative dc current. Measuring 1.8 x 1.0 x 0.8 in., products are designed for applications with yoke current requirements from 14.0 A (SDL-3006 and SDL-3008) to 18.0 A (SDL-3007 and SDL-3009) peak to peak. Products also offer extended operation for...
Read More »
Ensure Your Medical Device Meets Regulatory Standards with Triad's Custom Magnetics
Triad Magnetics' custom components for medical devices are designed and manufactured with the strictest regulatory standards in mind. Our capabilities include rapid design, prototyping, and testing of inductors, transformers, and power supplies for medical equipment. Check out our video to learn more.
Read More »
