Mechanical Components and Assemblies

Form-In-Place Gasket saves time in flange assembly.
Gaskets

Form-In-Place Gasket saves time in flange assembly.

Silicone-free Type HH190 anaerobic material forms instant, pressure resistant, leak-free seal and permits adjustment up to 60 min after assembly. It allows for metal-to-metal contact, eliminating problem of re-torquing. Purple, flowable paste is non-flammable and has viscosity of 200,000 cP. Fixture time is 90 min and full cure is in 24 hr. When cured, HH190 resists most chemicals, including...

Read More »
Linear Actuators/Slides offer rugged, simple design.
Actuators

Linear Actuators/Slides offer rugged, simple design.

TUFF-SERIES slides are offered in 4 sizes with strokes ranging from Â-½ to 24 in. and bore sizes from ½ to 1 ½ in. They use polymer bearings and common mounting bolt patterns. Rod-guided table slides are available with side or center mounted rodless cylinders. They feature .750 and 1.250 in. rod diameters, strokes from 1 to 36 in. and bores of 1, 1 ½, and 2 in. Each...

Read More »
Miscellaneous Tubes

Nanofocus X-Ray Tube produces sharp, magnified images.

Nanofocus tube obtains x-ray images of areas as small as 0.5 Â-µm (500 nm), providing magnification with sharp image resolution. X-ray beam angle on source provides added ability to inspect at high magnification levels using oblique views. Source comes with self-contained forced air-cooling system. When used with Advanced Defect Recognition (ADR) software, unit can analyze defects such as...

Read More »
Plungers

Spring Plungers are suitable for machines and fixtures.

Multifunctional DBM Universal Spring Cylinders have tapped holes and pilot bores on compression ends and threaded extensions on tension ends. Able to accept standard or custom attachments, hardened steel plungers (45 to 50 Rc) can also be used directly, such as in indexing applications. Optional, removable retract lock can be used on threaded and non-threaded styles. Retracted plungers rotate...

Read More »
Radius Inserts allow 90 degree milling.
Inserts

Radius Inserts allow 90 degree milling.

AP Milling Inserts with -46 geometry are offered in industry standard radii, including 0.031, 0.063, 0.094, 0.157, 0.197, and 0.252 in. Grade X500 is for extreme applications and grade SP6564 is for applications in steels, stainless steels, and high temperature alloys.

Read More »
Collapsible Containers offer various storage options.
Containers

Collapsible Containers offer various storage options.

Available with 0, 1, or 2 hinged drop doors and 4-way forklift access, ROPAK(TM) 4548 reusable containers have 45 x 48 in. footprints and are available in 7 heights from 25 to 50 in. Maximum load capacities range from 1,200 to 2,000 lbs with return ratios of 1.4:1 to 2.6:1. Available 45 x 48 x 33 in. dunnage model offers load capacity to 1,200 lbs and return ratio of 1.6:1. When collapsed,...

Read More »
Container permits transport/storage of wastewater chemicals.
Containers

Container permits transport/storage of wastewater chemicals.

Rotationally molded and seamless, UN/DOT-certified Unitote intermediate bulk container has all-plastic, polyethylene design that resists swelling and elongation due to chemical contact. Permits secure shipping and on-site storage of chemicals used in treatment of municipal and industrial water and wastewater. Container comes in 275- and 330-gal capacities, has 1.9 specific gravity rating, and...

Read More »
Manufacturing Equipment

Connector Interface speeds up termination of 32 to 48 AWG wire.

Smart Spike(TM) works with Smart Block(TM) for capture and insertion of fine wire. Optional electro-mechanical Smart Limiter(TM) mounts on Smart Block and limits use to predetermined setting, then renders device useless. Smart Block can be configured as integrated, pre-assembled platform for active or passive electronic components, combining solder or solderless wire terminations, flex circuit...

Read More »
Machining Bar suits demanding applications.
Miscellaneous Bars

Machining Bar suits demanding applications.

Project 70+® premium stainless steel machining alloys are offered in 6 grades and provide more lot-to-lot consistency, faster machining speeds, better part output and less tool wear than comparable products. Grades include Type 303, Type 304/304L, Type 316/316L, Type 416, Custom 630, and 15Cr-5Ni. Bar is offered in sizes ranging from .125 to 3.25 in. in standard increments.

Read More »
Oil Seals suit variety of general industry uses.
Hydraulic / Pneumatic / Radial Shaft Seals

Oil Seals suit variety of general industry uses.

Oil Seals available in over 100 different types, from single-lip designs to metal-clad seals, fit shaft sizes ranging from 3.2 to 317.5 mm. They meet ISO 6194 standards and are available in 4 base polymers: Nitrile, Polyacrylate, Silicone, and Fluoroelastomer. ASTM D2000-standard seals retain lubrication and exclude dirt and moisture. Oil Bath Seals, for wheel hubs, offer 4 unitized, one-piece...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers