Littelfuse Adds Fuse Holder, Block, and Clip Selection Tool to its Web-Based iDesign(TM) Circuit Protection Selection Platform
Helps find the right fuse holder, block or clip based on the selected cartridge fuse or circuit parameters CHICAGO- – Littelfuse, Inc., the global leader in circuit protection, has added a Fuse Holder, Block, and Clip Selection Tool to its popular iDesign™ online simulation and product selection platform.- With the addition of this new tool, Littelfuse iDesign now offers circuit designers...
Read More »Terminal Blocks have spring clamp compression mount contacts.
Utilizing METZ CONNECT Springcon technology for secure, vibration-resistant connection that automatically adjusts to 28–16 AWG wires, SC305 and SL305 series facilitate wire-to-board connection without header. Contact is established directly on solder pads, allowing opposing side of PCB to be used for components. With 5 mm centerline, solid wires insert directly for tool-less connection. While...
Read More »
Flange Mounting Blocks feature locking collars, set screws.
Flange Mounting Blocks in BBXBLK-HCF and BBXBLK-UCF Series include cast iron housing in addition to dual seal. Designed to fit shafts with -½-3-½ in. dia, standard duty 4-bolt units allow machinery to be efficient and safe.
Read More »
Module offers single-point wiring for safety devices.
Equipped with power supply and removable terminal blocks, RM-2AC serves as central point for terminating all signals to and from solid-state safety device. It converts solid-state outputs to force-guided relay outputs. One NO and one NO/NC safety relay output rated at 250 Vac, 6 A can be used as primary switching device or to switch contactor. With 100-240 Vac input, module can monitor switching...
Read More »
Injection Molding from 3D Printed Molds
Check out this white paper to see how 3D printing may be a beneficial alternative to traditional mold making processes.
Read More »Fuse Terminal Block has maintenance-friendly design.
DIN-rail mount fuse blocks in HMFA.2 series use spring clamp terminations and accept standard blade type fuse. Supporting voltages and currents up to 125 V @ 15 A, product is available with LED indication for troubleshooting and maintenance situations. It can be labeled in 3 locations and is designed to accept the PTC push-in jumper. Unit suits applications with PLCs and other micro-controllers...
Read More »
Setting Blocks cushion and support glass.
Setting Blocks protect glass against vibration and shock from handling, shipping, and wind loads. Available with or without pressure-sensitive adhesive, blocks elevate and isolate insulating glass units from sash. Neoprene material makes blocks resilient, allowing glass unit to handle stressed conditions. Offering temperature range of -20 to 170-
Read More »
Offset Block allows quick tool change.
Tool Length Offset Block eliminates lengthy tool setups, and chipped or broken tools. It allows user to touch off any type of tool in about 30 sec. All tools will be within .0001 in. of each other, eliminating question of which tool to adjust on first piece from setup.
Read More »
Fuseblock facilitates installation in SMD automation.
OGN-SMD fuseblock can be surface mounted with 5x20 mm pre-loaded fuses, eliminating need for mounting block, fuses, and cover in separate steps. Heat-resistant UL 94 V-0 plastic withstands heat of vapor phase and reflow soldering. Fuseblock is rated to 10A/250V. Rated power acceptance at ambient air temperature, with or without reflow cover, is 4W; with transparent cover, 2.5W. Pin spacings of...
Read More »
Fuse Blocks provide Type 2 motor-starter protection.
Class CC fuse blocks are molded in self-extinguishing polyester fiberglass, and offer touch-safe operation with no load fuse disconnect lever. Rated at 30A and 600V, they accept wire sizes of 6-14 AWG. With CC fuses, units carry motor starting inrush currents, providing current limitation to protect against low and high level faults. Fuse blocks are UL listed, cUL certified and carry CE mark.
Read More »
Safety Block System prevents stamping press operator injuries.
Lightweight 6061-T6 aluminum safety block is used during changeover and maintenance of die components to prevent injuries to press operators. It has compressive yield strength of 35,000 psi. Wedges compensate for gap left between safety block and upper press section ram. Optional power cutoff plug can be connected to press operation control circuit.
Read More »
5 and 13 Micron Resolve Columns with Greater Bed Stability
Jordi Labs provides materials solutions that set the standard for innovation and quality. Our line of GPC and GFC columns are on the cutting edge of precision manufacturing and a result of our uncompromising commitment to quality and customer service. See our video to learn more.
Read More »
