New Machinery & Machining Tools Products

Positioning System suits fiber optic assembly.

SixShooter(TM) 6-axis precision positioning system consists of 3 dual-axis modules, including vertical elevator stage; Y-axis with integrated Y theta rotary axis; integral compounded XZ horizontal dual axis stage; topped with dual tilt ZX Phit Tilt stage. All axes include linear or rotary, non-contacting, solid state encoders. System is controlled by MICROMATIC-5, 6-axis digital servo control...

Grease Pump dispenses precise amount.

PurgeX(TM) has single piece piston that dispenses up to 0.012 cu in. of grease per cycle. Grease is supplied from reservoir to injector pump. Reservoir location is not critical, and meters can be mounted in any position. Electrical energy from switch timer or computer will activate system. Buna N and Viton seals are used throughout for positive sealing. All air and impurities are completely...

Alignment Kit measures machinery.

Microgage provides precise measurements of machinery straightness, surface flatness, rail and slide parallelism, and squareness of equipment. It consists of compact laser transmitter and digital receiver that captures laser reference beam and provides digital readout of laser's position. Placing laser on moving slide or table allows digital receiver to measure worn areas, locations where binding...

Micro Grinder is available with various size motors.

Electer E-Max Ultra-Precision, Multi-Purpose Micro Grinder uses built-in microchip processor for optimum motor output. For easy handling and control, on/off switch is located directly on motor. Available speed ramges include 1,000 to 35,000 rpm, 1,000 to 29,000 rpm and, 1,000 to 15,000 rpm. Control unit includes digital speed display in x1000 rpm, soft touch buttons, and computer control.

Construction Materials for the Future

In this eBook, we highlight some key advantages of Cross-Laminated Timber (CLT) and show why every builder needs to consider adopting this remarkable construction advancement. We'll also introduce you to the latest innovation in CLT, GRIPBlock™, an exciting new technology that will change the way you look at CLT forever.

Drilling System drills deep holes fast.

Model 200 BTA system has drilling capacity of 2.5 in. dia and 84 in. effective drilling depth. It is equipped with special refrigeration for proper coolant temperature control. Counter-rotation of workpiece helps system attain close tolerances. System drills nickel-base Inconel 600 and 700 series workpieces at penetration rate of 1.5 in./min.

Horizontal Machining Center suits high volume production.

F3-660L offers spindle speeds from 0 to 20,000 rpm in 1.55 sec, 3.2G acceleration/deceleration rates, 90 deg table indexing at 0.8 sec, and chip-to-chip time of 2.4 sec. Rapid traverse rate for X, Y, and Z axis is 4720 ipm. Strokes for X and Y axes are 26 in.; Z axis stroke is 20 in. Tool magazine stores 40 tools with No. 40 taper. Tool life management software, 2-pallet changer, flood and base...

Cutting Machine handles stranded cables up to 3/0 AWG.

PowerCut 3500 automatically cuts large round cables up to 1.0 in. dia and flat ribbon cables up to 3.9 in. wide. It features electronic control and variety of interfaces for accessories. Feed belts are driven by servo-motor that transports material in length increments of 0.004 in. while providing extra feeding power needed for heavier cables. Pneumatic cutting machine can be used alone or fully...

Tying Machine has maximum tying diameter of 6 in.

TM 66 ties coils, hanks, or bundles of wire, cable and tubing. It automatically wraps tension elastic cord around material to be bound, ties knot in cord and cuts ends. Minimum tying diameter is 0.2 in. Machine includes adjustable tying tension and automatic cord loading. Electronic safety eye or sensor monitors and prevents machine from operating if there are objects or hands above cut-out.

Seal Plates facilitate O-ring installation.

Code 61 and Code 62 Seal Plates provide proper alignment and squeeze on O-rings when joining 2 surfaces. Outer diameter is grooved to center and improves O-rings' loading. Plates incorporate optional integrity support rings for structural support of 2 inner joined surfaces. These support rings eliminate seal damage.

Finishing Machine offers parts/media separation.

Model OR-5VLR long-radius vibratory unit features 5 cu ft bowl lined with thick molded urethane for parts protection. Separation technology allows for timed discharge of parts, without operator involvement. Variable speed machine has tube diameter of 54 in. and stands 41 1/2 in. high. Automatic lubrication system lubricates 2 vibratory bearings and assures failsafe protection against low air...

Locon Sensors Withstand Extreme Temperatures

Locon Sensor Systems offer robust sensor solutions for even the most severe environmental conditions. Their line of high-temp inductive sensors and their cylindrical photoelectric series can operate in temperatures up to 250 degrees Celsius. See our video to learn more.