Metal Oxide Varistors suit various power systems.
ROV Series MOVs provide over-voltage fault protection by clamping high-energy, short-duration impulses. Devices are available in 5-20 mm diameters and are rated from 18-1,800 V. They are also available in radial-leaded configurations and can be supplied in tape-and-reel packaging. Suited for use in line-voltage applications, products may also be used in security systems, power supplies, and surge...
Read More »Reel Feed System increases terminal crimping productivity.
Heavy-Duty Ring and Spade Terminals are available 2- or 3-up on single-reel, rear-feed system, which allows 2 or 3 terminals to be crimped onto ground wire at one time for high-voltage applications. Made from solid, smooth-finish brass, terminals are offered in sizes to crimp onto larger, higher voltage, 6-8 and 8-12 American Wire Gauge ground wire from single large-capacity rear-feed reels.
Read More »Digital I/O Card expands available I/O in SBCs.
Suited for use with company's SBCs (BL2500) and operator interfaces (OP7200), RN1100 RabbitNet I/O expansion mechanism is based on 3-wire, full duplex technology. Product utilizes off-the-shelf Ethernet cables, transmitting data at rates to 1 Mbit/sec over maximum recommended distance of 33 ft. Mounted on 100 mm DIN rail tray, unit features I/O set consisting of 24 inputs and 16 sink/source...
Read More »CompactPCI Card has 3U height.
RocketPortÃ-® CompactPCI (cPCI) serial card employs Kontron CP302 IntelÃ-® Mobile Pentium III processor based CPU board and CP-ASM-4 cPCI chassis. Product provides up to 16 RS-232 or RS-422 connections from single cPCI expansion slot. It conforms to PICMG 2.0 Revision 3.0 specification for cPCI expansion cards within PCI industrial computers.
Read More »3 Formulation Methods to Reduce Lean Giveaway for Processed Meat
Download this white paper, and learn about three methods that can help you improve your bottom line and yield by reducing lean tissue giveaway.
Read More »Panel-Mount Connectors suit high-frequency applications.
Two-hole, SMA connectors are fabricated to MIL-STD-348A, Section 310 with nickel- or gold-plated brass bodies, Teflon insulation, and gold-plated contacts. Model RSA-3261 SMA jack and Model RSA-3221 SMA plug have solder cups, while Models RSA-3262, RSA-3268, and RSA-3269 have solder posts with flush and extended dielectric terminations. Connectors are suitable for microwave applications where...
Read More »SMA Connectors are offered in panel-mount versions.
Suited for use in high-frequency and microwave applications where small size is required, SMA, 2-hole, panel-mount connectors are fabricated to MIL-STD-348A, Section 310 with nickel or gold plated brass bodies, Teflon insulation, and gold plated contacts. Model RSA-3261 SMA jack and RSA-3221 SMA plug have solder cups, while RSA-3262, RSA-3268, and RSSA-3269 have solder posts with flush and...
Read More »Choke Circuits offer dc resistance down to 0.20 ohm.
Packaged in lead-free, surface-mount, wire-wound designs, common-mode ICM-0805 and ICM-1206 suppress noise in USB 2.0, FireWireÃ-®/IEEE 1394, LVDS, and high-speed digital interfaces. With max dc resistance from 0.20-0.45 ohm, ICM-0805 is rated for currents from 450-280 mA and has common-mode impedance from 30-370 ohm @ 100 MHz. Max dc resistance for ICM-1206 models ranges from 0.3-1.2 ohm,...
Read More »Controller minimizes transformer size in power supplies.
Pulse Width Modulator Model LT1950 employs control mechanism that protects, simplifies, and reduces size of isolated/non-isolated 15-500 W power supplies with 24 and 48 V input supply rails. Adaptive maximum-duty-cycle clamp circuit prevents transformer saturation and protects MOSFET from failures. Adjustable current-slope compensation allows optimization of transient response. Operating...
Read More »USB Connector maintains low profile design.
Single-port KUSBL-SMT enables space savings of up to 64% using surface mount technology, while stacked KUSBL provides 31% space savings using through hole design. Both models are fully compliant with USB 2.0 and are available in standard gold flash or 30 Ã-µin. gold contact plating. KUSBL-SMT models are also available in tape and reel.
Read More »Resistor Chips provide film stability over time and temperature.
Thin film, wire bondable, multi-tap resistor chips simplify design and trimming of hybrid circuits. Series MTR offers up to 11 taps with resistance range from 100 ohms to 240 kohms in 2 configurations. Tightest available tolerance of total resistance is 5%, and tightest TCR value is Ã-
Read More »Innovative Dampney Coating Systems Suit Even the Most Specialized Applications
Dampney's high performance coating systems provide protection against extreme weather, chemicals, and corrosive environments for atmospheric, immersion, and underground applications. Check out the video to learn more.
Read More »