New Electronic Components & Devices Products

Low-Profile LEDs provide high flux over wide angle.

SuperFlux LEDs have water clear lenses and provide 7,000 mcd luminous intensity @70 mA current over 65 or 85 deg viewing angle, depending upon version. Measuring 7.62 mm sq. with 4.4 mm high body, through-hole LEDs can be mounted close together in clusters to fit wide variety of illumination applications in aviation, automotive, marine, industrial, and emergency signs. Colors include green,...

Core Pins are offered in 500 diameters.

M-2 high speed steel core pins are available in every decimal dia from 0.010 to 0.505 in. in 0.001 in. increments, with 0.0002 in. or 0.0003 in. dia tolerances. Double-tempered to Rc 60-63, pins are wear-resistant and permit close spacing without modification. They are available in 2, 2 1/2, 3, 4, 6 and 8 in. lengths and are suited for glass-filled applications.

Surge Protection Module mounts on DIN rails.

3880-DIN Surge Protection Receptacle Module employs Hospital Grade Receptacles to ensure fail-safe electrical connections of equipment in critical environments. Built for use on 120V single-phase AC power sources, module provides MOV-based Normal Mode and Common Mode protection. UL 1449 Suppressed Voltage Rating (SVR) is 400 volts peak L-N, L-G, and N-G. Module's green protection LED goes off...

RF Coaxial Adapters feature metrology-grade construction.

Precision N Adapters have gold-plated 303 stainless-steel bodies, BeCu center conductors, TeflonÃ-® insulators, and come in straight and right-angle designs with swept center contact. Mated pairs exhibit 1.20 VSWR, from dc to 18 GHz. Available in female-female, female-male, and male-male combinations, N Adapters provide MIL-STD-348 interface, are rated at 50 ohm, and operate over -55 to...

Design Guide: Heat Sinks for High-Power Applications

Without appropriate thermal management, electronic components will degrade over time, causing problems ranging from minor errors to critical failures.

Connectors meet IEEE 1394 standards.

4pin IEEE 1394 connectors operate at speeds up to 400 Mbps. Through-hole connectors, available for use with 0.8 and 1.6 mm thick PC boards, are made of black PBT thermoplastic, and feature indented metal pegs for PCB retention. SMT connectors are made of black PA6T high temperature plastic, and have enlarged solder tabs for PCB retention. Both styles are shielded to control EMI/RFI, and have gold...

I/O System uses standard M12 plug connections.

EASi/oN Modular Field Bus I/O system provides tool-free means to connect peripherals and other components. It combines plug-in bridging blocks, power feed, field bus connection, and connecting cables, along with integrated module catches and standard DIN rail mounting. System permits complete I/O systems to be removed from circuit without removal of other field bus subscribers. EASi/oN works with...

Metal Thread Inserts fit wood and composition board.

Three metal thread inserts install without need for special tools. Knife thread inserts, available with coarse and fine internal threads, furnish holding power in hard woods such as oak, maple, and mahogany. Finsert thread inserts provide strong metal threads in softer materials, and prevent splintering, splitting, and thread pullout. Hex Drive thread inserts are for soft materials such as pine,...

Cord Grips connect and seal.

Tuff-Seal strain-relief cord connectors, liquid tight connectors and watertight conduit hubs are available in six different materials of construction: diecast zinc for residential and commercial applications; aluminum for general industrial facilities; nylon for environments with high moisture content; steel for durability in tough environments; valox for use in washdowns; and stainless steel,...

LVDT Signal Conditioner operates without line power.

Low voltage LVC-2401 operates from 24 to 30 Vdc power, and is suitable for use in industrial applications where space and power sources are limited. It has user-selectable +/-7.5 Vdc and 4 to 20 mA outputs, LVDT excitation frequency of 2.5, 5 and 10 Hz, and works with any LVDT or RVDT. Unit operates over temperature range of 0 to +160Ã-

Disconnect Switches can be used in hazardous areas.

MD2DS Series factory-sealed disconnect switches are engineered to meet NEC and IEC performance standards. Fused and non-fused 600VAC models are offered in 30, 60, and 100 Amp designs. MD2DS switches incorporate stainless steel bolts and hardware, copper-free aluminum enclosure with epoxy powder finish, and insulated, dual-color operating handle that indicates when switch is energized. Handles can...

Ensure Your Medical Device Meets Regulatory Standards with Triad's Custom Magnetics

Triad Magnetics' custom components for medical devices are designed and manufactured with the strictest regulatory standards in mind. Our capabilities include rapid design, prototyping, and testing of inductors, transformers, and power supplies for medical equipment. Check out our video to learn more.