Electronic Components & Devices

Coupling Bodies offer various mounting options.

Coupling Bodies offer various mounting options.

Series APC panel mount coupling bodies are injection molded from acetal thermoplastic and resistant to mild chemical solutions. They withstand max temperatures of 180Â-ºF and pressures from vacuum up to 120 psi. Units enable tubing to be connected and disconnected from panel during use and maintenance. Terminations include hose barbs and ferruleless polytube compression fittings. Plastic...

Read More »
Audio Power Amplifier targets multi-channel applications.

Audio Power Amplifier targets multi-channel applications.

Single-chip Model STA5150 delivers 200 W into 4 ohm load with less than 10% distortion. It combines Indigo's BASH topology and Bipolar-CMOS-DMOS process technology. BASH technology uses DMOS power transistors operated in class AB mode, reducing EMI and distortion typical of class D switching amplifiers. By continually adjusting power supply voltage, depending on amplitude of amplified audio...

Read More »

I/O System supports use of open-source technologies.

Linux-based SNAP-ARL-ASDS programmable I/O processor mounts on standard SNAP B-series mounting racks and interfaces with mix of analog, digital, and serial SNAP I/O modules. Featuring RS-232 serial port and 10 Mbps Ethernet connection, system supports multiple file transfer protocols, including FTP and Samba. Programmers can use Linux-based tools to develop custom applications for SNAP-ARL-ASDS...

Read More »
Programming System supports F2812 DSP.

Programming System supports F2812 DSP.

Suited for use with 32-bit F2812 digital signal controller, PS300 automated programming system accommodates up to twelve 4-socket adapters and is designed specifically for Flash-based applications. Architecture provides system scalability and software-based process control.

Read More »

FPGAs offer digital signal processing speeds to 333 MHz.

Stratix(TM) FPGA models EP1S80 and EP1S60, available with 79,040 and 57,120 logic elements, respectively, are available in -5 speed grade to DSP speeds to 333 MHz and data rates to 300 MHz. Built on 0.13-micron, all-layer copper process, devices provide up to 22 embedded DSP blocks, which consist of hardware multipliers, adders/subtractors, accumulators, and pipeline registers. They offer...

Read More »
Lead Set allows 4-wire resistive measurements.

Lead Set allows 4-wire resistive measurements.

Model 6730 low-ohm Kelvin Lead Set incorporates gold-plated clips and nickle-plated Beryllium copper wire wrapped in silicone. Leads utilize wide-opening 0.800 in. alligator clip design plus retractable-sheath banana plugs for connecting to various calibration test equipment. Color-coded set is rated at 1000 V, CAT III, with 20 A current maximum and is suitable for calibration, design, and test...

Read More »
Line Splitter allows testing of loads up to 1,800 W.

Line Splitter allows testing of loads up to 1,800 W.

MetermanÂ-® ELS2 AC Line Splitter works with any ac current clamp or clamp meter to measure residential current without splitting ac line cords. Rated for 120 V at 15 A, unit provides 10 times current magnifying loop for accurately measuring low current. Built-in jacks are provided for voltage sag testing. Splitter includes nylon carrying case and is useful to residential, commercial, and...

Read More »
HCMOS Oscillators provide -162 dBc/Hz noise floor.

HCMOS Oscillators provide -162 dBc/Hz noise floor.

Models CCHD-950 and CVHD-950 are ultra-low phase noise oscillators in clock and VCXO versions, respectively. Both come in FR5 9 x 14 mm SMD package and generate frequencies between 50-100 MHz with 80 and 100 MHz offered as standard. Units require input supply voltage of 3.3 Vdc and 15 mA current. Extended operating temperature range of -40Â-

Read More »
Bolt-Type Connectors are rated for currents to 400 A.

Bolt-Type Connectors are rated for currents to 400 A.

Bolt-type panel/plate mountable feedthru and junction block connectors have modular design and do not require mating connectors. Stud-type junction block connectors incorporate steel plated studs on non-feed-thru models; feed-thru connectors have copper alloy. Products are available in 1/4-20, 3/8-16, 1/2-13 in. sizes with respective termination ratings of 100 A, 1,500 V; 250 A, 1,500 V; and 400...

Read More »

All Topics