New Electronic Components & Devices Products

Cable Management Rack has Zone 4 seismic rating.

Featuring steel knock-down design that can be assembled onsite, Mighty Mo 6 is compliant to Telcordia GR-63-CORE Zone 4 standards, with load rating of 510 lb. Unit is 7 ft high with 10.5 or 16.25 in. channel depth and full 45 rack units of mounting space. Suited for high-density cabling system applications, rack features vertical management cage with individual 1-rack unit fingers and...

AC Surge Suppressor provides Live-Neutral-Ground protection.

Designed to safeguard microprocessor-based equipment, Theon INL08000 works by opposing changes in electron flow on ground wire while not compromising intrinsic ground safety. With 15 A, 120 Vac continuous current rating, unit utilizes multi-stage, non-degrading surge suppression along with common-mode filtering to eliminate power surges and sags. Multi-stage circuit has active response time of...

Electronic Ballasts operate 1-4 low-wattage T8 lamps.

CentiumÃ-® Instant Start Electronic Ballasts are produced in low watt models for operation of 1-4 T8 fluorescent lamps rated 32, 25, and 17 W as well as same number of 30, 28, and 25 W Energy-Saving T8 lamps. With ballast factor of .77, units feature IntelliVolt technology, which enables operation at any input voltage from 120-277 V, 50/60 Hz. Products also utilize instant start circuitry and...

Line Driver drives 4 TTL/CMOS signals into 50 ohm loads.

With 10 kohm input impedance, self-contained Model PRL-444 can receive signals from devices with low drive current such as sensors, PC-based digital I/O cards, and optical transceivers. Each input has 10 kohm pulled up to 2.5 V so it can also be driven by open-collector devices. With 50 ohm terminations, all outputs can drive 100 ft of 50 ohm cables at clock rates greater than 60 MHz. Driver...

Metal Finishing Selection Guide

This unique chart compares different metal finishes by cost, corrosion resistance, applications and more.

Connectors enable port selection in hard drive carriers.

Suited for use in enterprise servers and storage systems, 22-position SATA receptacle connectors and 29-position SAS plug and receptacle connectors provide options for vertical or right-angle connector termination. Two options are provided for HDD interface within drive carrier: use of SAS receptacle provides 2 ports and capability to accept SAS or SATA drives, while SATA receptacle supplies...

Connectors can be customized to fit application.

Suited for computer, telecom, and digital image industries, lead-free connectors are RoHS-compliant. They can be used for connecting computer boards and peripheral devices, as well as inner and outer connections for cell phones. Units are available with various pin counts and pitch sizes for board-to-board, board-to-wire, FPC, I/O, SIM card, battery, and USB connections.

Preamplifier features built-in, 20 Hz high-pass filter.

Featuring pre-polarized design, Model 426A10 is a Ã-½ in. preamplifier that operates from ICPÃ-® sensor power. Built-in filter minimizes unwanted low frequency sounds that may saturate analyzer. Unit terminates in BNC connector and uses standard coaxial cable. Operating temperature is -40 to +80Ã-

Shortwave IR Emitters produce 0.9-1.6 microns max.

Featuring back-mounted gold reflector, Shortwave Infrared Emitters offer heated lengths from 1-120 in., infinitely adjustable control, and linear power up to 400 W/in. They require practically no heating-up or cooling down times. With tube format of 23 x 11 mm, twin tube units feature filament temperature from 1,800-2,200Ã-

Short Wave Emitter features plug-in connection.

Twin-tube, Short Wave Infrared Emitter measures 23 x 22 mm and is rated up to 10 A with 55-480 V possible. It features gold reflector, single end connection, quick disconnect, and tool-free replacement.

AdvancedTCA Module addresses 10 Gbps applications.

Based on dual Intel IXP28xx network processors with 1.4 GHz core and 700 MHz Xscale(TM), Promentum(TM) ATCA-7010 can be configured as single, dual, parallel, or pipelined. Ten 1 gigabit Ethernet interfaces that connect via rear transition module enable 10 Gbps packet processing. Model ATCA-7010 supports PICMG 3.0 and PICMG 3.x through modular fabric interface card. It includes 3 banks of 256 Mb...

Reduce Time to Market, Improve System Uptime with Dedicated Computing Medical Solutions

Embedded computing solutions from Dedicated Computing are designed to meet unique and specific requirements. As the preferred supplier to leading healthcare OEMs, the Dedicated Computing team of expert engineers gets your product out to the market faster while helping your company avoid costly validation and verification steps. Check out our video to learn more.