Electronic Components & Devices

PC/104 Module targets global positioning applications.

PC/104 Module targets global positioning applications.

OrbiTrak(TM) GSM combines wireless tri-band GSM/GPRS connectivity with 12-channel parallel-tracking GPS receiver in single, integrated embedded board. Supporting full interrupt-sharing for all serial ports, board includes 4-channel 16C550 UART with 2 RS-232 serial ports for other devices. A 16-bit wide programmable digital I/O is provided to interface with low-power digital devices, along with 2...

Read More »
Cable Management Rack has Zone 4 seismic rating.

Cable Management Rack has Zone 4 seismic rating.

Featuring steel knock-down design that can be assembled onsite, Mighty Mo 6 is compliant to Telcordia GR-63-CORE Zone 4 standards, with load rating of 510 lb. Unit is 7 ft high with 10.5 or 16.25 in. channel depth and full 45 rack units of mounting space. Suited for high-density cabling system applications, rack features vertical management cage with individual 1-rack unit fingers and...

Read More »
AC Surge Suppressor provides Live-Neutral-Ground protection.

AC Surge Suppressor provides Live-Neutral-Ground protection.

Designed to safeguard microprocessor-based equipment, Theon INL08000 works by opposing changes in electron flow on ground wire while not compromising intrinsic ground safety. With 15 A, 120 Vac continuous current rating, unit utilizes multi-stage, non-degrading surge suppression along with common-mode filtering to eliminate power surges and sags. Multi-stage circuit has active response time of...

Read More »
Electronic Ballasts operate 1-4 low-wattage T8 lamps.

Electronic Ballasts operate 1-4 low-wattage T8 lamps.

CentiumÂ-® Instant Start Electronic Ballasts are produced in low watt models for operation of 1-4 T8 fluorescent lamps rated 32, 25, and 17 W as well as same number of 30, 28, and 25 W Energy-Saving T8 lamps. With ballast factor of .77, units feature IntelliVolt technology, which enables operation at any input voltage from 120-277 V, 50/60 Hz. Products also utilize instant start circuitry and...

Read More »
Line Driver drives 4 TTL/CMOS signals into 50 ohm loads.

Line Driver drives 4 TTL/CMOS signals into 50 ohm loads.

With 10 kohm input impedance, self-contained Model PRL-444 can receive signals from devices with low drive current such as sensors, PC-based digital I/O cards, and optical transceivers. Each input has 10 kohm pulled up to 2.5 V so it can also be driven by open-collector devices. With 50 ohm terminations, all outputs can drive 100 ft of 50 ohm cables at clock rates greater than 60 MHz. Driver...

Read More »

Connectors enable port selection in hard drive carriers.

Suited for use in enterprise servers and storage systems, 22-position SATA receptacle connectors and 29-position SAS plug and receptacle connectors provide options for vertical or right-angle connector termination. Two options are provided for HDD interface within drive carrier: use of SAS receptacle provides 2 ports and capability to accept SAS or SATA drives, while SATA receptacle supplies...

Read More »
Connectors can be customized to fit application.

Connectors can be customized to fit application.

Suited for computer, telecom, and digital image industries, lead-free connectors are RoHS-compliant. They can be used for connecting computer boards and peripheral devices, as well as inner and outer connections for cell phones. Units are available with various pin counts and pitch sizes for board-to-board, board-to-wire, FPC, I/O, SIM card, battery, and USB connections.

Read More »
Preamplifier features built-in, 20 Hz high-pass filter.

Preamplifier features built-in, 20 Hz high-pass filter.

Featuring pre-polarized design, Model 426A10 is a Â-½ in. preamplifier that operates from ICPÂ-® sensor power. Built-in filter minimizes unwanted low frequency sounds that may saturate analyzer. Unit terminates in BNC connector and uses standard coaxial cable. Operating temperature is -40 to +80Â-

Read More »

Shortwave IR Emitters produce 0.9-1.6 microns max.

Featuring back-mounted gold reflector, Shortwave Infrared Emitters offer heated lengths from 1-120 in., infinitely adjustable control, and linear power up to 400 W/in. They require practically no heating-up or cooling down times. With tube format of 23 x 11 mm, twin tube units feature filament temperature from 1,800-2,200Â-

Read More »

All Topics