New Electrical Equipment & Systems Products

Connector adapts torch to cutting system.

SureLok(R) torch, with ATC(TM) Advanced Technology Connector, designed with sequential interface connections, allows end users to adapt cutting torches to almost any manufacturer's air-plasma cutting system. Torches with connector are available with outputs up to 100 amps. Connector is less than 2 in. in diameter.

DC-AC Inverters power multi-tube LCD modules.

MD Series drives up to 16 CCF tubes with combined power of 10-60 W. High-efficiency inverters can be dimmed using external analog control signal that interfaces with onboard pulse width modulator. Inverters can dim to less than 0.5% duty cycle, for dimming ratio of 200:1. Depending on backlight, dimming ratio of 1000:1 can be achieved. Five mounting holes on each module make installation simple....

Level Switches suit extreme application conditions.

Horizontal and Vertical liquid level switches feature modular 3-piece design and are available in 316 stainless steel, Hastelloy, PP, and PTFE. They offer high or low level alarms and include 2 independent circuits on each switch. Units provide electrical, on-off pneumatic, and proportional pneumatic controls. ANSI and square flanges are available.

Motors employ rare earth magnets.

RE-max 0.94 in. dia motors employ rhombic moving coil design with ironless rotors, which allow for zero cogging. Four versions are available with metal or graphite brushes and single or double shafts. Power ranges vary from 6.5 to 11 W, and continuous torque is rated to 1.7 oz-in. (max). Ambient temperature range is from -22 to 185 deg F, and maximum efficiency is up to 90% depending on the...

Guide To Swageless Fittings

Electroline specializes in innovative, easy-to-install swageless fittings. The following guide will highlight everything you need to know about swageless fittings.

AC Inverter suits harsh environments.

MV-4X has NEMA 4X/12 and IP66 ratings, allowing it to resist dust and forced water or chemicals. On board RS-485 Modbus RTU allows for networking up to 32 nodes. Users can select between open loop vector control or volts/hertz control with simple parameter change. Programmable analog and digital inputs and outputs are available. Inverter is offered in 230 Vac, 3-phase from 1/2 to 10 hp, and in...

Right Angle Gearmotor provides high torque.

M4000 G14 PM DC Series single worm right-angle gearmotor is available in 12 to 180 V models, with continuous torque of 16 to 60 lb-in. and speeds up to 500 rpm. Typical applications are wheelchairs, scooter drives, welding wire feeders, conveyor drives, packaging equipment, and floor cleaning equipment. It has bronze gear, high energy ceramic magnets, ball bearings, Class F insulation, balanced...

Lightning Arrestors are inline or bulkhead mount types.

Series NE9960 lightning arrestors, suited for use in 50-ohm RF transmission lines, utilize plasma discharge switching technology, and provide short to ground at 75 V (max). Units feature RF insertion loss of less than 0.2 db from DC 3 GHz. Other models can be tuned for performance at specific frequencies from DC to 6 GHz. Construction offers type N male on one end and female bulkhead mount on...

Cable Block is self-adjusting.

Multi-angle, aerial cable block reduces friction when pulling cable around tight corners by adjusting itself from maximum 12 in. bending radius down to straight line. Pole-mounted corner block can be used in stringing applications that place cables up to 5 in. in diameter, such as 3 bundled 750 MCM cables. All-aluminum, heavy-duty block attaches to pole with inclusive steel chain binder.

Flatness Measuring Kit checks machine beds and fixtures.

Laser Microgage Flatness Kit consists of Laser Transmitter mounted onto precision turntable, which allows laser beam to rotate and defines plane of light that is flat to 0.001 in. over range of 20 ft. Digital receiver can be moved around to various locations and provides height reading relative to flat plane of projected laser light. Computer interface software gathers readings and exports them...

Entrance Splice Cabinets resist water and dust.

Used for splicing optical fiber cables at building entrances, cabinets can be mounted on wall in cable vault or in cable entrance facility to provide transition splicing between outside plant cables and building cables. Splices are stored in modular slide-out splice trays that accommodate up to 864 individual splices or 2,592 mass fusion splices. Any combination of individual fusion trays and...

Does Your Parking Lot Make a Good First Impression?

To enhance its appearance by removing oil stains, Terminator-HSD uses micro bacteria to remove the stain without harsh chemicals, acids, or detergents. Check out the video to learn more.