Electrical Bushings

Dry-Type Condenser Bushings target power transformers.
Electrical Bushings

Dry-Type Condenser Bushings target power transformers.

Available in voltage classes ranging from 25–138 kV, O Plus Dry™ Bushings incorporate resin impregnated synthetic condenser body and high temperature vulcanized silicon weather shed. Design eliminates potential leaks of oil-filled bushings and porcelain shards from fragile porcelain insulators. Use of HTV weather sheds also minimizes need for cleaning in highly contaminated environments and...

Read More »
Cable Bushing maximizes wire density.
Electrical Bushings

Cable Bushing maximizes wire density.

With SKINTOP CUBE MULTI, up to 23 electrical cables or pneumatic lines can pass directly through enclosure wall. System places rigid, glass-reinforced nylon frame into standard-sized cutout in wall. Polycarbonate insert inside rectangular frame has gel-filled holes, which allow cables to be inserted while creating seal and providing strain relief. Available in 2 versions, CUBE MULTI-  covers...

Read More »
Electrical Bushings

Nonmetallic Split Bushings eliminating need for rework.

Available in 2–4 in. trade sizes and made of PA 66 synthetic polyamide (105°C rated), Mighty-Rite® Nonmetallic Split Bushings can be installed before or after pulling wire. Snap-on, hinged design adjusts and aligns without requiring any installation tools,- while self-aligning latching mechanism also permits one-hand installation. Internally threaded for use with threaded conduit or...

Read More »
Electrical Bushings

Split Grounding Bushings eliminate rework.

Available in trade sizes from -¾–4 in., Mighty-Rite® SGB Series helps contractors safely install electrical systems. Units can be installed before pulling wire or after, eliminating rework. This feature also makes pulling larger conductor wire easier when contractors can install grounding bushings after pull. Equipped with 150°C rated liner, cULus Listed bushings feature captive screws and...

Read More »
Thin Panel Bushings convert raw-edged holes into smooth holes.
Electrical Bushings

Thin Panel Bushings convert raw-edged holes into smooth holes.

Made from nylon 6/6, Thin Panel Bushings are designed for panels as thin as .020 in. and are available for .218-.875 in. diameter holes. Bushings feature locking fingers that snap into holes with fingertip pressure in fractional increments up to maximum panel thickness, and can withstand push back force of greater than 35 lb. In addition to creating smooth insulated holes, bushings insulate and...

Read More »
Multi-Cable Bushing System offers wide variable clamping range.
Electrical Bushings

Multi-Cable Bushing System offers wide variable clamping range.

Resistant to oil, grease, UV rays, and ozone, SKINTOP® CUBE consists of frame and flexible clip sealing modules, which are available in 4 clamping ranges of 4-6, 6-9, 9-12, and 12-16 mm. After installation, cable is secured against vibration, strain relieved, and sealed in accordance with IP64. Matching, glass-fiber-reinforced polyamide frames, available for 16-pin or 24-pin connector openings,...

Read More »
Electrical Bushings

End Bushings minimize installation efforts.

Intended for use with company's proprietary walking beams, part No. 34013-188L rubber rotating bar pin end bushing conserves installation time by eliminating need to pay attention to bar pin angle. Once pressed in, bar pin can be turned with shop wrench or similar tool to required axle angle. Product includes set of shims to facilitate axle alignment as well as required fasteners to complete...

Read More »
Strain Relief fits round and double D holes.
Electrical Bushings

Strain Relief fits round and double D holes.

Designed to protect flat, round, or multiple cables at panel entry points, Snap-In Ratcheting Strain Relief can be pre-assembled offline for final assembly at later time - or remote location. Fingertip pressure allows installation into standard round or Double D hole with no tools required. Accommodating wire range from .115-.575 in., wire locking ratchet fits panel mounting hole size of .875 in....

Read More »
Electrical Bushings

Repair System returns fastener holes to nominal size.

Designed for -¼-3/8 in. dia fastener holes, ForceMate 2 Panel Repair System can fix damaged countersunk holes in access panels and other thin-skinned surfaces. It installs 2 nested bushings into hole in one operation via cold expansion tooling to bring fastener holes that have been ovalized, oversized, shifted off-center, or otherwise damaged back to nominal size. ForceMate 2 bushings increase...

Read More »
Precision Machining Solutions with Over 25 Years of Experience
Sponsored

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.

Read More »

All Topics