New Material Processing Products

Floor Tiles provide assisted cooling for computer rooms.

FloorTrays(TM) integrate FlexTray(TM) fantrays into standard 2 x 2 ft computer room floor tiles. They are useful for cooling assists on high power computer cabinets or at ends of plenums where air pressure may be too low to provide adequate cabinet cooling. FloorTrays(TM) are available in 3 and 6 fan versions with floor tile styles to fit most floor systems. FlexTrays(TM) operate on 85-264 Vac...

Sealed Tank Mixers offer various sealing options.

DT top-entering, sealed tank mixers are available with V-Ring Seals (DTL), 4-Ring Stuffing Boxes (DTA), Double Mechanical Cartridge Seals (DTN), Single Mechanical Seals (DTNS), and Single Mechanical Cartridge Seals (DTNC). Modular design facilitates any application. Features include direct or gear-reduced drives, speeds to 1750 rpm, power ratings from 1/4 to 5 hp, and flanged or chuck shaft...

Fan Trays utilize modular design.

FilterTray(TM) line of 3U fan trays with integrated filters can incorporate range of FlexTrays(TM) and SmarTrays(TM). FlexTrays provide advanced cooling, worldwide AC input, or -48 Vdc telecom input. SmarTrays add microprocessor control, variable speed, and RS232 communications. Users can optimize FilterTray to specific applications.

Refrigerated Air Dryers filter compressed air.

Magnum SC and CT Series remove water and water vapor from compressed air. CT has multi-stage separator-coalescing filter installed after chiller to remove oil, water, and particulate contaminants. Both have Smart CycleÃ-® demand control system and control center with flow schematics and digital telemetry for remote analysis of dryer performance. Dryers are available in 10 models from 2,500 to...

Managing the New FGD Wastewater Regulations

A guide for managing Flue Gas Desulfurization wastewater using leading technologies.

Jet Mill suits 10 to 20 gram batches.

Qualification MicronizerÃ-® with 2 in. milling chamber, can mill up to 1/2 lb of material per hour, yet is capable of feed rates as low as few grams per hour with maximum sample recovery. Fines have narrow particle-size distribution, with particle diameters as small as few microns. Replaceable venturi allows mill to accept wide range of feed sizes, and peripheral feed design prevents...

Spray Dryer controls and measures relative humidity.

Model FT80 Spray Dryer has Tall Form chamber straight side to diameter ratio of 3:1 and conical discharge section. Features include 2-fluid nozzle atomization system, nozzle configurations for counter- and co-counter atomizing, and individual inlet and exhaust fans with variable speed control. IP65 control console provides full instrumentation, data logging for key operational parameters, and...

Floor Shaker utilizes triple eccentric drive.

MaxQ 5000 incubated and refrigerated floor shaker has 30 x 18 in. stainless steel platform that accommodates six 6L Erlenmeyer or 2800 ml Fernback flasks. Foot pedal automatically opens door for hands-free operation. Unit handles loads up to 75 lbs. Speed range for analog models is 40 to 400 rpm and 15 to 500 rpm on digital models. Low temperature model offers optional light bank for day/night...

Water Bath Shaker provides 24/7 operation.

Lab-Line MaxQ 7000 has 18 x 18 in. stainless steel platform that accepts deep well plates, flasks, beakers, centrifuge tubes, test tube racks, and gel trays. Bath temperature is controlled to Ã-

Airblasting Systems suit high volume applications.

Bulk Abrasive Airblasting Systems use piping designed to provide lowest possible pressure drop. They feature multi-outlet Thompson Valve(TM) II controls that allow each operator independent control of abrasive media flow. All systems have normally closed, fail-safe metering and control valves. Standard bulk systems include 120, 160, 500, 650, and 800 ftÃ-³ models. Optional trailers are...

Platform Shakers provide 24/7 operation.

Lab-Line MaxQ2000 and MaxQ3000 open air platform shakers offer load capacities of 35 and 50 lbs., respectively, and will accommodate platform sizes from 11 x 13 in. to 36 x 24 in. Speed range for analog models is 40 to 4,000 rpm and digital models is 15 to 500 rpm. Units operate in temperature range of 0 to 40Ã-

ISO-Certified Plastic Injection Molding from Rodon

The Rodon Group is a proven leader in high-volume, close tolerance injection molding. We offer globally competitive, innovative manufacturing solutions for a broad range of industries. Check out our video to learn more.