New Machinery & Machining Tools Products

Deburring Machine cooks off defects.

Instant ConTEMporary Deburring machine can deburr, dewhisker and remove metallic contaminants from cast iron, steel, stainless steel and aluminum parts, and deflash zinc parts, all with burst of high heat. It completely removes burrs, even deep inside parts. In typical deburring cycle, parts are sealed in chamber. Mixture of oxygen and natural gas is introduced into chamber, ignited, and flash...

Motorized Compact Spindles can work alone or in groups.

3 models of high efficiency/high torque, precision, Motorized Compact Spindles (MCS) are equipped with 40mm triplex class 7 DTDB front bearing arrangements, and feature permanent magnet DC brushless motors to supply balanced power and torque. MCS-1 delivers up to 49 in-lbs of torque and 3.1 hp at 5,000 rpm; MCS-1HS delivers up to 4.4 hp at 12,000 rpm and 23 in-lbs of torque; heavy-duty MCS-2...

Locking Kits fit Haas machining centers.

Ball Lock(TM) fixture kits contain all components needed to locate and lock fixture plates to subplates. System provides quick change capability, and holds plates together with working loads up to 20,000 lbs. Standard kit includes correctly-sized subplate and fixture plate, both pre-drilled with ball lock bushings installed and correct number of shanks, T-slot nuts, sine fixture keys, and socket...

Collet Chucks bolt directly to lathe spindle nose.

Direct mount collet chucks can be used on any spindle that uses draw tube type actuator. With pull back design, compact units are suited for clamping small diameter workpieces, increasing tool clearances and reducing strain on spindle bearings. Rigid clamping allows increased machine speeds for bar feed applications. Chucks are available in types 5C, 16C, 3J, 20C and 25C. Threaded nose is...

3-axis vs. 5-axis

Our latest Ebook breaks down the difference between 3-axis and 5-axis CMM measurement methods.

Holding Assemblies are used in metal product manufacturing.

Permanent Magnetic Holding Assemblies are designed for positioning, stabilizing, holding, and feeding materials, parts, and scrap. Various standard configurations and sizes are available with insulated Ceramic, Alnico, and Rare Earth Magnets. Assemblies for watertight and high-temperature applications are also available.

Table offers quick manual height adjustment.

Speedy Crank System 2000 sit-stand table offers top crank ratio of 4 cranks and front crank ratio of 6 cranks for every 1 in. of height adjustment. Height range is 16 in. with widths ranging from 30 to 72 in. and depths of 24 or 30 in. 14 gauge steel upright tubing and 16 gauge cross tubing are powder-coated for scratch and chip resistance. Speedy Crank is rated for dynamic weight load of 200...

Punching Machine processes material up to 0.312 in. thick.

TRUMATIC 5000 Rotation (TC 5000 R) machine offers 4600 ipm positioning speed, hydraulic punching head capable of 1200 punching strokes per minute, and 50 x 100 in. working range. Two separate motors are controlled synchronously and without mechanical link. Racks and pinions interlocked at an angle provide stiffness for drive system and improve gantry's ability to withstand stress. Hydrostatic...

Finishing System operates at 190-

BC40 TRU TEMP(TM) produces high-quality black-oxide finish on iron and steel components in 10 to 15 min. Non-polluting system produces satin, true-black magnetite finish of 0.000020 in. thickness. Compact, 7-tank system eliminates severe splattering and boil-over hazards. Process is suitable for dimensionally-critical parts, including power drive components, gears, and machine parts, and meets...

Wire Termination Machine features linear slide table.

LPT-522 magnet wire termination machine inserts MAG-MATE terminals into coil-wound components found in motors, stators, bobbins, and other magnet wire applications. It is capable of producing up to 600 assemblies per hour, and can perform up to 2 secondary operations such as continuity testing, wrap-off post trim, and tab bending. Machine handles in-line, radial and linear/angularly opposed...

Cord Reel holds 40 ft of extra heavy duty cord.

Craftsman Professional Cord Reel with triple-tap power outlet has 12-gauge, 3-wire power cord with maximum rating of 1875 watts, 15 amps and 125 volts. Triple-tap has 3 grounded outlets with re-settable circuit breaker protection. LED indicator illuminates when power is live. Reel is made of thermoplastic that withstands heavy-duty use. Cord automatically retracts for tangle-free storage.

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.