Electronic Components & Devices

Battery Formation Rectifier suits automotive applications.
Rectifiers and Diodes

Battery Formation Rectifier suits automotive applications.

BC/HD (battery charging/high density) system is suitable for formation of automotive, or flooded, lead-acid batteries. It can also be used for VRLA and high-production, water-bath formation installations. System is available with output currents of 10 to 60 A and output voltages up to 450 Vdc. Depending upon output and control requirements, it uses either Micro Me cabinet controller or...

Read More »
MOSFET BGAs work with battery packs.
Arrays

MOSFET BGAs work with battery packs.

FDZ2551N and FDZ2553N dual N-channel and FDZ2552P and FDZ2554P P-channel 20 V MOSFET ball grid arrays have physical and electrical characteristics that are suitable for Li-Ion battery pack protection applications. Each BGA is housed in 4 x 2.5 mm surface mount package, and has common drain connection and 0.8 mm mounted height. RDS(On) is 28 mohm and 14 mohm for N and P channel devices,...

Read More »
Converters

Analog-to-Digital Converter employs SAR architecture.

Model MCP3221, 12-bit converter offers I2C(TM) interface in SOT-23 package. Its design permits operation with typical standby and active currents of 5 nA and 175 micro-amps respectively. Fast mode (400 kHz clock rate) enables sampling rates to 22.3 kilo-samples per second (ksps). Suited for remote applications, unit has single supply operation and operates over range of 2.7 to 5.5 V and offers...

Read More »
Adjustable Arm ergonomically positions monitors.
Mounts

Adjustable Arm ergonomically positions monitors.

Gas Assist Monitor Arm allows operators to adjust position of computer monitors horizontally and vertically over range of 12 in. Support plate for monitor has locking tilt function for precise positioning. Arm can be installed on wall, table, or desk and adjusted exactly to operator's comfort level. It supports up to 65 lb, and has abrasion resistant baked enamel finish.

Read More »
Lamp Ballasts meet new pulse start specs.
Lighting Ballasts

Lamp Ballasts meet new pulse start specs.

Linear Reactor ballasts for pulse-start metal halide lamps have automatic reset thermal protection that interrupts power to ballast in event of abnormal lamp or ballast failure. They meet existing and newly proposed pulse-start ANSI specifications. Ballasts are available for various metal halide lamp wattages, including: 150 W (ANSI Code M102/M142), 200 W (M136), 250 W (M138/M153), 320 W...

Read More »
Single Chip USB UART upgrades RS232 systems.
Electronic Adapters

Single Chip USB UART upgrades RS232 systems.

FT232BM transfers serial data over Universal Serial Bus. It can be used to upgrade older RS232 serial designs to USB with minimal development and cost. It incorporates reset and clock circuits, 5V/3.3V UART output voltage, data transfer rates of up to 920 k baud for RS232, and 3,000 k baud for RS422/RS485. Royalty free drivers are available.

Read More »
Headers, Sockets, and Terminals provide 200 I/O in
Electrical Connectors

Headers, Sockets, and Terminals provide 200 I/O in

Four-row surface mount FourRay(TM) headers and sockets (TOLC/SOLC Series) offer board stack heights of .250, .315, .394, and .472 in. SOLC series socket construction offers tuning fork style Tiger Buy contacts. FOLC Series socket construction offers 3-finger Beryllium Copper Tiger-Eye contacts. MOLC Series connectors are available in pin counts from 20 to 50 positions in multiples of 5 per row...

Read More »
Electrodes

Electrode Assemblies/Separators are designed for EDLCs.

EXCELLERATOR® electrode assemblies and separators for Electrochemical Double Layer Capacitors (EDLCs) provide strength and dimensional stability and allow for high carbon loading. Bound directly to current collector, electrodes are available in various thicknesses, densities, and shapes in single- or double-sided electrode assemblies. EXCELLERATOR® Separators are chemically resistant...

Read More »
Cabinet supports 19 or 23 in. widths.
Cabinets

Cabinet supports 19 or 23 in. widths.

Model DC-8010 rack has panel mounting rail design that allows users to choose desired panel width. Four panel mounting rails come with cabinet. All-welded steel frame cabinets come in panel height of 78.75 in. with overall height of 84 in. Cabinet width is 27 in. and overall depth is 30.75 in. Neutral sand texture cabinet weighs 256 lbs and has 1,200 lb equipment load capacity. Cooling is...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers