Materials & Material Processing

Materials & Material Processing

Ross Completes Large Order of High Speed Dispersers

Sep 28, 2016

Hauppauge, NY – Ross recently shipped 49 High Speed Dispersers to a global manufacturer of paints, coatings and chemicals. The major order covered High Speed Dispersers suitable for different size batches ranging from 2,000 liters (528 gallons) up to 10,000 liters (2,642 gallons) and equipped with motors from 5 HP to 150 HP. Other features include:

  • Disc-type saw-tooth blade for powder... Read More

Adhesives & Sealants, Materials & Material Processing

LORD Corporation Scheduled to Present on a Variety of Topics at Upcoming International Elastomer Conference

Sep 28, 2016

Cary, N.C. – LORD Corporation – a leader in the development of adhesives, coatings, motion management devices, and sensing technologies – has announced a full schedule of presentations at the upcoming International Elastomer Conference. To be held Oct. 10-13 at the David L. Lawrence Convention Center in Pittsburgh, Pa., the show is an annual event held by the Rubber Division of the ACS... Read More

Materials & Material Processing

Air Products introduces catalysts and additive technologies for foam emission management.

Sep 28, 2016

Enabling the use of low-Global Warming Potential (GWP) Hydrofluoroolefin (HFO) Blowing Agents in polyurethane foam applications, Air Products introduces catalysts such as: Polycat® 203; Polycat® 218; Polycat® 204; and, Dabco® PM301 that can help manufacturers achieve low or non-emissive foam products. Air Products also releases a new additives selection guide highlighting the... Read More

Materials & Material Processing

Ferrite Beads suit high-reliability applications.

Sep 27, 2016

Designed to meet requirements of DSCC 03024 specification, HRB-US Series begins as full reel ferrite bead lots acquired through OEM approved distribution channels and traceable to selected manufactures of commercial devices. Devices pass through pre- and post-screening processes while undergoing AEM’s Tin-Lead conversion. Products are then subjected to DSCC 03024 Group A, B, and C testing.... Read More

Materials & Material Processing

Polyurethane Dispersion is designed for automotive applications.

Sep 27, 2016

Designed as fiber sizing for reinforced composites in automotive under-the-hood applications, Hydrosize® Link is available in 2 grades and designed to react with PA6 and PA6.6 resin matrices. Hydrosize Link U470 is suited for use with chopped strand fiber, and Hydrosize Link U480 is intended for chopped strand and continuous fiber. Both grades deliver optimized composite performance even... Read More

Chemicals & Chemical Processing, Materials & Material Processing

Chromaflo Featuring Non-phthalate Tinting System and Global Presence at CPI 2016 Visit us in Baltimore at Booth 27

Sep 27, 2016

Ashtabula, Ohio, U.S.A – Chromaflo Technologies will present a broad product portfolio for the polyurethane industry at CPI, September 26-28, 2016. Chromaflo will introduce the DTP colorant line, a non-phthalate plasticizer tinting system to enable customers to create new colors on demand as well as feature our global presence, high-strength blacks and wide range of chemistries/carriers.... Read More

Materials & Material Processing

Injection Molding Machine ranges from 67-596 U.S. tons.

Sep 26, 2016

Featuring energy-saving Mars technology, Mars II Eco is U.S./UL safety compliant with 460 V power as standard. Servo-hydraulic injection molding machine is equipped with 2 air circuits for part ejection: one on stationary platen and one on movable platen. Additional air circuits are optional. System includes KEBA 1075 control and SPI robot interface as standard. Read More

Materials & Material Processing

Electric Injection Molding Machine features hydraulic circuit.

Sep 26, 2016

Available from 45–730 U.S. tons, Zhafir Zeres Series includes integrated hydraulic circuit to facilitate molding applications which require core pull or sophisticated ejector functions. Hydraulic core pull interface (circuit) is installed on moving platen and provides more flow and increased pressure compared to external power pack solutions. Pressure and flow rates are adjustable via... Read More

Machinery & Machining Tools, Materials & Material Processing

REP Unveils New Machines, Technology at 'K 2016

Sep 26, 2016

Responding to advancements in machine design and expanded market opportunities, industry leader in rubber injection presses adds to lineup REP international is preparing for the K2016 show The largest plastics and rubber industry companies will be present in October for the “K Show”, held once every three years in Düsseldorf. As the leading manufacturer of rubber injection molding... Read More

Materials & Material Processing, Robotics

Absolute Haitian Provides Press, Servo Robot for ACS Tech Center

Sep 26, 2016

Minneapolis, Minnesota – Absolute Haitian, the exclusive distributor of Haitian and Zhafir injection molding machines in the U.S. and Canada, and ACS Group, a manufacturer of comprehensive auxiliary equipment for the plastics industry under the AEC, Cumberland, and Sterling brands, are partnering to install an operating molding line for a new Technology Center in New Berlin, Wisconsin. The line... Read More

Materials & Material Processing

Black 100% Recycled Content Masterbatch delivers sustainability.

Sep 26, 2016

Made of 100% recycled carbon black from post-consumer tires, ECOBlack product provides sustainable alternative to conventional carbon black. ECOBlack 40 consists of polyethylene-based masterbatch and can be used in such traditional applications as film, sheet, and molded items. Material supports use at typical masterbatch letdown ratios of from 2%–5%. Possible areas of use include... Read More

Lubricants, Materials & Material Processing

Die Release Agents utilize heat-activated additive.

Sep 26, 2016

DIE SLICK® die lubricants with Smart Polymer™ Technology, a heat-activated additive, are able to form evenly distributed, tough, protective die coating when exposed to hot areas of die and do not accumulate residue in cooler areas. Within die casting industry applications, these poperties reduce solder on castings while enhancing release and wetting characteristics. Use also results in... Read More

Materials & Material Processing

CO2 Supply Agreement Finalized

Sep 26, 2016

CO2 Supply Agreement Reached between Pennsylvania Grain Processing, LLC and Continental Carbonic Products, Inc. DECATUR, Illinois and Clearfield, Pennsylvania – Continental Carbonic Products, Inc. (CCPI), a subsidiary of Matheson Tri-Gas, Inc., announced that it has entered into an agreement with Pennsylvania Grain Processing, LLC (PGP) for the supply of carbon dioxide (CO2) from... Read More

Fluid & Gas Flow Equipment, Materials & Material Processing

Polymer Material suits high-temp jet engine applications.

Sep 23, 2016

Suitable for bearing chambers, sump systems, and internal gearboxes in jet engines, Fluoroloy® A90 enables spring-energized seals to work with continuous temperature above 608°F. Product withstands static hot air sealing in temperatures up to 662°F while retaining mechanical properties with same or less leakage, surface indentation, and material degradation. Material exhibits low linear... Read More

HVAC, Material Handling & Storage, Materials & Material Processing, Welding Equipment & Supplies

Blast & Wash Systems Exhibiting at the AmShow in Rochester, NY

Sep 23, 2016

Blast Wash Systems will be exhibiting at the  AmCon 2016 Show September 21st & 22nd in Rochester, New York We invite you to see our equipment in action - parts washing equipment, weld fume extractor, downdraft table and blast cabinet. Blast & Wash Systems is the largest distributor of finishing equipment in the region. Blast & Wash Systems offers automated finishing equipment to solve... Read More

Materials & Material Processing

SEBS Block Copolymer suits food contact, medical applications.

Sep 23, 2016

With respective MFR values of 27 and 77 g/10 min @ 230°C, 2.16 and 5 kg, Kraton™ G1653 styrene-ethylene-butylene-styrene (SEBS) block copolymer retains tensile strength (>30 MPa) and toughness while offering solution viscosity of 480 cP. Solid level can reduce coating layers for coating applications or reduce shrinkage and need for solvent for sealant applications. Supplied in free... Read More

Materials & Material Processing

Davis-Standard At International Elastomer Conference, Booth #706

Sep 22, 2016

Pawcatuck, Conn. – Davis-Standard, LLC will promote the company’s full range of elastomer extrusion technology during the International Elastomer Conference, Booth #706, on October 11th-13th, in Pittsburgh, Pennsylvania. Davis-Standard will discuss its DSREV rubber extruder with a model 2000 crosshead and Uth rollex® 70 gear pump/strainer system with a two-roll feeder (TRF). Davis-Standard... Read More

Materials & Material Processing

ChromaLuxe Achieves Three Times the Print Display Permanence Rating Compared to Silver-Halide Color Papers

Sep 22, 2016

Latest generation ChromaLuxe® aluminum sublimation photo panels printed with Epson UltraChrome DS and Sawgrass Photo XF inks achieve Wilhelm Imaging Research, Inc. (WIR) Display Permanence Ratings that are more than three times better than current silver-halide photo papers. LAS VEGAS - (SGIA EXPO, BOOTH #3031) - ChromaLuxe today announced a major advancement in photographic printing... Read More

Adhesives & Sealants, Materials & Material Processing

Dosing of Abrasive Thermal Pastes in Cyclic Operation

Sep 20, 2016

Dosing of abrasive thermal pastes in cyclic operation The ultimate stress test for stator materials Abrasive thermal pastes are found in a range of applications. In the production of LEDs and circuit boards in the electronics industry and in the area of control systems in automotive applications - to name but a few examples. Through the regulation of thermal resistance, these pastes, referred to... Read More

Machinery & Machining Tools, Materials & Material Processing

Vapor Phase Soldering System offers inline convection alternative.

Sep 20, 2016

Along with 6–9 min cycle times or less, programmable 4040 provides SMT assemblers with optimized soldering quality, instant product changeovers, and 0% risk of overheating. Design enables installation in any workspace without requiring complex ductwork and external venting, while heat transfer efficacy and gentle conditions of vapor phase process minimize exhaust generation. Other... Read More