Material Processing

Resin Dryer matches speed of plastics processors.
Air / Hot Air Dryers

Resin Dryer matches speed of plastics processors.

LPD(TM) Low Pressure Dryer dries resin batches of 400 lbs within 4 hours, and requires 80% less energy than 100 lb/hr desiccant dryers. It uses vacuum to pull moisture from within pellets and carries out heating and vacuum drying simultaneously in separate stations. It essentially transforms batch processes into continuous processes. Dryer makes it possible to change materials or colors without...

Read More »
Mats

Non-Skid Safety Mat works when submerged.

Non-skid surface on presence-sensing industrial safety mats is totally submersible as to reduce risk of slipping on surfaces covered with grease and oil. Applications include robotic welding, laser welding and cutting, pick and place robots, plastics blow molding machines, assembly machinery, water jet machines, automated material handling, packaging machinery, textile machinery, paper converting...

Read More »
Heat Exchangers keep uninsulated enclosures cool.
Exchangers

Heat Exchangers keep uninsulated enclosures cool.

ProAir heat exchangers can significantly reduce heat rise in sealed, uninsulated enclosures and extend life of enclosed electronics. Model XR20 will limit heat rise to 24°F above ambient and XR29 will keep temperature within 15°F above ambient. Both are available in 115 or 230 V and 50/60 Hz configurations and can be mounted to any internal or external surface of enclosure. Heat...

Read More »
Mixers (Fluid Blending)

Static Mixer offers concave mixing elements.

Kenics® KMX static mixer's concave elements promote cross-stream flow. Each element is approximately 1 pipe diameter in length, and consists of multiple intersecting blades, which generate fluid layers as mixture flows downstream. Features include ASME-certified design and fabrication, diameters up to 24 in., no moving parts, and no external power or regular maintenance. Sheets of low...

Read More »
Circulation Attritor can adapt to existing Q machines.
Material Processing Mills

Circulation Attritor can adapt to existing Q machines.

QL circulation grinding Attritor includes holding tank that is typically 10 times Attritor size. Specially configured arms speed up grinding and create more agitation. Unit's high circulation/pumping rate consists of holding tank contents passing through Attritor at ~8 times an hour. Grinding media for QL range in size from 3/32 to 1/4 in. in diameter. Typical media include chrome steel,...

Read More »
Mist and Smoke Eliminator is rated at 1250 CFM.
Dust / Fume / Mist Collectors

Mist and Smoke Eliminator is rated at 1250 CFM.

MistBuster II utilizes 3-stage filtration process to eliminate mist and smoke from airstreams. Mechanical mist impingers capture larger mist droplets, electrostatic precipitator (ESP) provides intense electrical charge on remaining contaminates, and aluminum post-filter entraps particles that may have been agglomerated on cell plates. MistBuster runs at noise levels rated to 70dBA @ 6 feet on...

Read More »
Stripping Pot cleans magnet wire.
Miscellaneous Agents

Stripping Pot cleans magnet wire.

Magnet Wire Stripping Pot removes film insulations from magnet wires of all sizes, types, and configurations. Wires are dipped into stripping solution to remove insulation without causing any mechanical stress or abrasion to wire. Units are available in 2 models: DSP1 has temperature control and DSP2 has programmable control for selecting and maintaining exact temperature. Both models are...

Read More »
RF Drying System improves insulation production.
Microwave Dryers

RF Drying System improves insulation production.

Macrowave applies radio waves at 40.68 MHz to remove water from fiberglass batting, board and vermiculite, and prevents migration of aqueous binders. It works on webs up to 12 ft wide. Because water is more responsive to RF energy than most materials, moist areas absorb more RF power than dry areas, which results in uniform drying. Method promotes consistent drying regardless of non-uniform...

Read More »
Fluid Bed Drying System recycles exhaust air.
Dryers

Fluid Bed Drying System recycles exhaust air.

Drying system recycles 75% of heated exhaust air through continuous pulse jet dust collector and reheats it in natural gas burner, during drying of rice, salt, limestone, sawdust, polymers, inorganic chemicals and other products that require temperatures of 150+ Â-ºF. System permits process to operate at high outlet moisture while staying comfortably above dew point of final exhaust air.

Read More »
Heat Exchangers cool compressed air.
Dryers

Heat Exchangers cool compressed air.

Models SR-125 to SR-3000 cool compressed air by mechanical refrigeration, removing moisture and assuring that none condenses downstream unless air is exposed to lower temperatures. They have integral demister moisture separator and two-pass air system. Compressed air is pre-cooled in aluminum-finned, cross-flow heat exchanger to reduce refrigeration load, resulting in more efficient refrigeration...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers