Material Processing

Plastic Belt is USDA compliant for direct food contact.
Belts

Plastic Belt is USDA compliant for direct food contact.

Model PWO500 modular plastic wire replacement belt features open hinge design that promotes abrasive release and cleanability. Belt provides product support as well as ample openings for drainage and airflow. Inverted funnel surface openings allow breading or debris to fall through instead of accumulating on belt. With Â-½ in. pitch and concave bottom surface, belt can run over ½ in....

Read More »
Separator is suited for mineral screening applications.
Screening Separators

Separator is suited for mineral screening applications.

ROTEX® Minerals Separator(TM) is designed for mined minerals and abrasives and maximizes product recovery at material temperatures to 400°F. Elliptical-linear motion provides equal feed distribution to all screen decks, uniform bed-depth across entire screen surface, and aggressive blinding control. Features include stacked, multiple-deck, tray access design; lift-rail system with...

Read More »
Side-Entry Mixers target oil and petrochemical industries.
Impeller / Propeller / Turbine - Agitators / Mixers

Side-Entry Mixers target oil and petrochemical industries.

Cutlass Fixed-Angle Mixer offers 10° fixed position that handles homogenizing, blending, and temperature uniformity of crude oils and refined products in storage tanks. Cutlass Swivel-Angle Mixer provides 60° rotation to effectively scour tank floor and keep sediment, water, and solids in suspension. Both feature electric motor, PM Lancer Prop(TM) Impeller, and tank shutoff device for...

Read More »
Fluid Processor suits cleanroom applications.
Handling Equipment

Fluid Processor suits cleanroom applications.

Stainless steel, split-system Microfluidizer® 600 and 700 model series can be set up so that operating assembly is in separate room from processing assembly; one hose, up to 30 ft long, runs through wall to connect separated assemblies. Processor reduces particles to sub-micron or droplet sizes, while intensifier pump drives product stream at velocities and pressures up to 40,000 psi...

Read More »
Dry Baths provide temperatures from -10 to +100°C.
Impeller / Propeller / Turbine - Agitators / Mixers

Dry Baths provide temperatures from -10 to +100°C.

Suited for use with biological and other samples, EchoTherm(TM) SC20 Digital and SC25 Fully Programmable Dry Baths are Peltier driven. They offer control to 1°C; mix speeds from 200-1,000 rpm; and backlit, 2-line, alphanumeric display. Variable-speed orbital mixer allows for simultaneous mixing and controlling of sample temperatures. Features include 30-day count down timers with alarm and...

Read More »
Processor Blade supports AdvancedTCA platforms.
Computers

Processor Blade supports AdvancedTCA platforms.

Suited for carrier-grade solutions, ATC-4130 is based on Intel® E7501 Chipset with 400 MHz front-side bus, utilizes 2.0 GHz LV Intel Xeon® Processor, and is compliant with PICMG® 3.0/3.1 specifications for AdvancedTCA platforms. System memory of up to 4 GB is supported via 2 ECC-protected DDR SDRAM modules. Unit uses Pigeon Point's management architecture, and offers 10/100...

Read More »
Fluid Mixer handles demanding applications.
Mixers

Fluid Mixer handles demanding applications.

Series BRM, available up to 200 hp, features AGMA Class No. 10 spiral bevel and helical gear set. Low-headroom, right-angle drive is housed in steel casing, available in 7 different size configurations, and withstands harsh interior and exterior environments. Tapered roller bearings carry rating of more than 100,000 hr, with minimum 1.5 service factor. Drywell construction around low-speed shaft...

Read More »
Mixers offer flexibility for various industries.
Mixers

Mixers offer flexibility for various industries.

QoEoDPlus(TM) Mixers incorporate leak-proof drywell design and 30,000 hr min L10 bearing life. Tapered-shaft engagement system ensures ease of disassembly and provides secure connection between shaft and drive. Features include shaft speeds of 44, 70, 88, and 117 rpm; cast-iron housing; and choice of NEMA C-flange motors from 1-5 hp. Units offer open-tank, nozzle, and pad-mounting options....

Read More »
Abrasive Blast Equipment

Air Blast Cleaning System extends maintenance intervals.

Auto Air Blast System blows jet stream of air for 1-3 min over dissolved oxygen sensor membrane at set intervals. Programmable timer in analyzer controls cleaning frequency, and compressor located near sensor provides air supply. Model 499ADO membrane dissolved oxygen sensor features molded Noryl construction and is suited for flow-through or submersion mounting. It incorporates integral...

Read More »
Abrasive Blast Cleaner processes small parts.
Material Processing Barrels and Drums

Abrasive Blast Cleaner processes small parts.

Wheelabrator® Barrel Blaster consist of 13Â-½ in. diameter, 12 bladed wheel unit, powered by 15 hp, 3,600 rpm, NEMA T-frame, direct mounted motor. Barrel is 32 in. diameter and 37 in. deep, providing 3 ft³ tumbling capacity for up to 600 lb. Adjustable, pneumatically-operated butterfly valve allows for positive media flow control. System provides contaminant removal, peening,...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers