New Electrical Equipment & Systems Products

DC/DC Converters enable smaller portable electronics designs.

FunctionPAK(TM) synchronous dc-to-dc boost converters provide high power density of more than 380 W/in.Ã-³ in 0.58 x 0.48 in. footprint. Models FX5545G006 and FX5545G106 convert input voltages from 2.5-6 V to low-ripple output voltages from 3.3-6 V. Output power and max current are 7.5 W and 1.5 A for FX5545G006 and 10 W and 2 A for FX5545G106. Units stabilize rechargeable battery outputs,...

Rotary Switches have binary output and tiny size.

Series P60A switches measure .394 x .394 x .236 in. and are offered in 10-position, binary-coded decimal or complement models and 16-position, hexadecimal or complements models. Sealed units have terminations that include common and 1, 2, 4, and 8 marked outputs and detent action that is compatible with clockwise or counterclockwise rotation. Rated 24 Vdc @ 150 mA max, units have life of 10,000...

Battery Charger fits in ThinSOT(TM) package.

Monolithic Model LTC4054 4.2 V single-cell, linear Li-Ion battery charger includes on-board charge termination circuitry and power transistor housed in 5-lead, 1 mm high package. It delivers up to 800 mA charge current without external transistor. Thermal regulation maximizes charge rate without risk of overheating. USB-compatible unit keeps battery fresh after charge termination by monitoring...

Plug/Cap provides customized product protection.

Series PnC is designed as both plug and cap. Made of dip-molded vinyl, it withstands temperature of 325-500Ã-

Pressure Sensor Selection Guide

This white paper provides information and a guideline for pressure sensor selection.

Electromechanical Switches suit hand-held devices.

Surface Mount Electromechanical Switches are offered in toggle, pushbutton, slide, DIP rotary, and tactile actuation types, which provide positive indication of circuit status. Made of heat resistant resins, they allow for exposure to vapor phase and reflow soldering. Molded-in, epoxy-sealed terminals conform to standard PC board grid spacing. Gull wing terminals ensure mechanical stability and...

Photodiode Head fits into tight locations.

Model PD300-TP laser power measuring head is 4 mm thick and can make power measurements on cw lasers in tight spaces. Sliding filter measures 50 pW to 300 mW and also contains measurement in dBm. Spectral range is 350-1100 nm. Unit provides Ã-

Compact Switcher offers standby and auxiliary outputs.

With active power factor correction, 125 W LPS125, 85-264 Vac power supply is suited for 1U rack installations and low-profile applications. With 6.7 W/in.Ã-³ density, unit delivers full rated output of 130 W with 30 CFM forced air or 80 W with convection cooling. It measures 3 x 5 x 1.29 in. and can be set up for lengthwise or crosswise airflow. Device also includes Class B EMI filter,...

Carrier Class Enclosure offers 20-slot backplane.

CompactPCI 23 in. wide, 8U high enclosure includes six 250 W hot swappable power supplies, which provide up to 1,250 W of redundant power. Backplane supports center-mounted processor board and 1 bridge board. Four individually hot swappable fans mounted below card cage and four individually hot swappable blowers mounted above card cage provide cooling. Monitor and alarm board and monitoring...

USB Connectors require minimal space on PCBs.

Mini USB Series consists of Type A, B, and AB connectors that are shielded for EMI protection, polarized to prevent mis-mating, and rated for 5,000 mating cycles. They support data rates up to 480 Mbps and power requirements up to 500 mA. Product variations include board-mount receptacles and cable plugs, both of which meet USB 2.0 requirements. Connectors are suitable for handheld computers,...

Connector Adapter Kits bridge diffferent thread sizes.

TwistMateÃ-® Adapter Kits facilitate connection of different sized male and female NPT threads with TwistMate test connectors and plugs. Adapter kits bridge different sized internal and external threads in any size combination between 1/8-1 in. Kits also connect female-to-female and male-to-male. TwistMate connectors are offered with 1/8-3 in. male and female NPT threads and handle leak-free...

Optimize Your Storage or Distribution Facility with Steel King Rack Solutions

Steel King racks are designed to meet seismic requirements in the most demanding conditions. Our durable storage products help your company save on maintenance costs. Check out our product video or download our Rack Planning eBook to learn more.