Rotary Hammer features pistol grip design.
Model BHE22 features 5.2 A motor and quick-change, 3-jawed keyless chuck system that allows operator to rapidly install accessories. It incorporates 360Ã-
Read More »
Toggle Clamps have low-profile design.
Series 2002, 2007, and 2010 manual hold-down toggle clamps feature low profile that offers respective holding capacities of 600, 1,000, and 1,400 lb. Clearance between handle and bar in open position eliminates additional pinch points, and pivot point is closer to mounting surface to improve vertical spindle contact on workpiece. Products offer multiple mounting hole patterns, and handles...
Read More »Heat Gun Kit offers 500 and 1,000 -
Ecoheat(TM) EC-100K Kit contains Model EC-100 flameless heat gun, 7/8 in. air reducer, 1 in. heat shrink attachment, 1 15/16 in. and 3 1/8 in. spreader attachments, and manual packed in plastic carrying case. Built-in hand guard protects hands and fingers, while recessed switch guards against knocks and bumps. Kit is suited for drying, activating adhesives, bending plastics, curing defrosting...
Read More »Nozzles optimize thin-plate metal cutting.
With FineCut(TM) Consumables, hand- and machine-torch operators cutting thin-plate, mild and stainless steel will obtain narrow kerf and small heat affected zone. FineCut also eliminates secondary operations such as dross removal. Consumables are used on Powermax 380, 600, 1000, 1250, and 1650, as well as comparable legacy systems. Starter kit includes 5 nozzles, 2 swirl rings, 5 electrodes,...
Read More »
A Solutions Provider
This white paper provides an overview of filtration and energy solutions.
Read More »
Separator protects a/c recovery/recycling equipment.
Connected between recycling equipment and vehicle, Recycle Guard(TM) determines which vehicles contain sealant, deteriorated lubricant, or excess dye and traps contaminants before they enter recovery machine. Sealant, dye, and lubricant separator features 2 high-porosity filters that trap sealants, dye, and lubricants. It catches both Type 1 (moisture reactant/leak stop) and Type 2 (seal sweller)...
Read More »
Vertical Vise facilitates wire EDM.
Model H4537, for Fixturing System 4000, provides positive clamping of one or 2 independent workpieces in same set-up. Vise incorporates 2 separate clamping jaws that require only the turning of a central screw for tightening. No supporting spacers or jackscrews are needed. Clamping jaws, with workpiece-height ranges of 0-.826 in. and .826-1.615 in., minimize obstruction above top of workpiece....
Read More »
Wheel Tractor Scrapers have dual power capabilities.
Models 621G, 627G, 631G, and 637G offer operator stations that promote efficient operation, low-profile scraper bowl, and EMS III electronic monitoring system. Electronically controlled engines feature Caterpillar HEUI(TM) fuel system and comply with current EPA emissions regulations. Other features include automatic planetary powershift transmission, single lever implement control, bulldozer...
Read More »
Metal Cutting Blades cut ferrous and non-ferrous metals.
Constructed with vibration dampening geometry, EnduranceÃ-® Carbide Tipped 8 in. Metal Cutting Circular Saw Blades resist bending and twisting and do not produce clouds of abrasive dust. They deliver straight cut with clean, burr-free edge with minimal heat and sparks. Blades with 42 teeth are recommended for metals over 3/32 in. thick, while 50-tooth blades are suited for thinner materials....
Read More »
Pneumatic Scissors can cut cleanly through Kevlar.
AirshirzÃ-® Scissors help reduce muscle fatigue when cutting KevlarÃ-®, carbon fiber, fiberglass, and other engineered composite materials. They feature 440 stainless steel blades and automatic spring-return action. Blade speed and position are fully controllable and can be stopped and opened at any time during cutting process. Safety latch secures blades in locked position for safety and...
Read More »
Riveting Machine delivers over one ton of force.
Model B-310 Pneumatic Orbital Riveting Machine provides visual status and precise adjustment of orbital forming process. Available with real-time process monitoring and process control, machine orbitally forms parts up to .312 in. diameter or equivalent area in tube, square, or other form. Tool stroke is adjustable from .06 to 1.75 in. in .001 in. increments. Standard throat depth is 6 in. and...
Read More »
Let Our Safety Experts Lower Your Risk
Elite Technical Services provides your company with qualified and experienced safety experts. Specializing in confined space and high-angle technical rescue and jobsite hazard assessment, your workplace safety is the top priority. Check out the video to learn more.
Read More »
