Spray Guns

Pressure Feed Spray Gun offers multiple set-up options.
Spray Guns

Pressure Feed Spray Gun offers multiple set-up options.

Fully coated inside and out with QuickClean™ Technology, TEKNA-® ProLite resists corrosion and facilitates cleaning, resulting in minimized paint defects. Gun features TE40 high efficiency air cap, HV40 HVLP air cap, 1.0 and 1.4 mm fluid tips, and analog gauge. With multiple set-up options, gun can work with variety of refinish coatings.

Read More »
Efficient On-Site Painting
Spray Guns

Efficient On-Site Painting

Ransburg No. 2 Gun Deuce Unit Makes On-Site Painting a Snap Dedicated to producing the highest quality products, ITW Ransburg continually delivers products for today's finishing requirements. The electrostatic No. 2 Gun may not be new to the industry, but with its 95% transfer efficiency, it adds new meaning to environmental stewardship . In fact, it's the only gun in the industry that can paint...

Read More »
Simulation Helps Develop Spray Gun with 50% Larger Pattern in Significantly Less Time
Spray Guns

Simulation Helps Develop Spray Gun with 50% Larger Pattern in Significantly Less Time

Graco engineers used FloEFD computational fluid dynamics (CFD) software from the Mechanical Analysis group of Mentor Graphics Corporation to optimize the design of a new plural component spray gun in 1/3 the time that would have been required to produce an acceptable but not optimized design using the trial and error method. The use of software prototypes made it possible to explore a much wider...

Read More »
Spray Guns

HVLP Spray Guns address automotive industry needs.

Trigger-actuated Velocity HVLP (high-volume, low-pressure) spray guns are designed to meet challenges of automotive collision and repair industry. With inlet pressure range of 20-43 psi, DT 3000 works perfectly with clearcoats, basecoats, primers, and waterborne paints. Standard tip sizes range from 1.3-2.0, and spray distance is 5-7 in. Suited for small repairs, MINI DT 3000 has best spray...

Read More »
Spray Guns

Power Wash Gun produces over 13 lb of cleaning power.

Operating on compressed air supplied by either an in-plant or 185 tow-behind compressor and standard municipal utility water, HydroForce Power Wash Gun is both hot and cold water capable, has no duty cycle limitations, and offers one trigger operation. Features include 48 in. stainless steel extension, adjustable auxiliary handle, and water shutoff valve for optional use of compressed air only...

Read More »
High Production Rate Powder Spray Gun can be used anywhere.
Spray Guns

High Production Rate Powder Spray Gun can be used anywhere.

Xiom 5000 Scorpion uses propane and air to provide wide spray and eliminates need for pre-heating under normal ambient conditions. Gun permits user to start/stop spraying process and diffuses gases so that flame heats coatings to their melting point and sprays them onto surface without clogging nozzle. System is adjustable for feedstock material, weather conditions, or metal substrate...

Read More »
Spray Guns

Binks to Showcase Depth of Guns, Pump Options at Upcoming IBEX 2006 Trade Show

October, 2006, Glendale Heights - Binks will be featuring its Air Assisted Airless LEL (Low Emissions Laminators) Gel-Coat and chopper equipment, and the Boss High Volume FRP Pump at the upcoming IBEX 2006 Show, being held at the Miami Beach Convention Center from November 1-3. IBEX is dedicated to the next generation of boatbuilding technologies. Show attendees will be able to learn about Binks...

Read More »
Electrostatic Spray Guns are designed for efficiency.
Spray Guns

Electrostatic Spray Guns are designed for efficiency.

Vector Systems optimize atomization and transfer efficiency through Vector gun design that redistributes pressure in air cap and adjusts balance between atomization and fan air. While reduced-weight design lends to operator comfort and reduces fatigue, weight distribution optimizes balance and ergonomics. Guns incorporate minimal parts for reduced likelihood of failure and maintenance. Oversized,...

Read More »
Automatic Spray Gun is suited for UV-coating applications.
Spray Guns

Automatic Spray Gun is suited for UV-coating applications.

Used in wood and metal industries, MAG AA UV Spray Gun employs carbide needle, leak-resistant carbide seat, and solvent-resistant O-rings. It supports atomization of various coating viscosities and features stainless fluid passages for water- and solvent-based materials. While wood industry applications include cabinets, flooring, milled products, and doors, metal industry applications include...

Read More »
Paratherm™ HR Heat Transfer Fluid: Higher Temperature Stability Leads to Longer Fluid Life
Sponsored

Paratherm™ HR Heat Transfer Fluid: Higher Temperature Stability Leads to Longer Fluid Life

For the ultimate in heat transfer fluid performance, Paratherm offers HR Heat Transfer Fluid that is engineered specifically for closed loop liquid phase heating. When it comes to characteristics such as thermal stability and fluid degradation, Paratherm HR leads the industry in value and performance. See our video to learn how Paratherm is raising the bar for heat transfer fluids.

Read More »

All Topics