
Solid Carbide Drill addresses small lot production needs.
Available in- 0.12–0.63 in. diameters for everyday machining applications involving older machines, small quantities,- or frequent workpiece changes, DC150 can be universally used for all materials and in all industries (especially general machining). Respectively featuring external and internal cooling, 3xD and- 5xD variants are both available in cylindrical shank (DIN 6535 HA) or Whistle...
Read More »AE50: ASABE Ranks Technologies from CNH Industrial Brands Among Top 50 Innovations of the Year
The American Society of Agricultural and Biological Engineers have included five technologies from Case IH and four technologies from New Holland Agriculture in their annual AE50 Awards. This prestigious awards series acknowledges the year's top 50 smart engineering product innovations to be introduced on the US market in 2014. BASILDON, United Kingdom - CNH Industrial N.V. (NYSE: CNHI / MI:...
Read More »Drill Bits drill through multiple materials at same time.
Compatible with all standard- -½ in. and 3/8 in. chuck drills, Multi-Material Drill Bits are available in 3–5 in. jobber lengths and 16 in. extended length, with diameters ranging from 1/8–1/2 in. Units have diamond-ground, 4-facet carbide tip with sharp cutting edges that guarantee centered starts with no walking. Designed with double-milled flute that removes dust and debris, bits...
Read More »Ulterra PDC Drill Bit Saves Operator Over $500,000
FORT WORTH, Texas - For the first time, a single Ulterra bit has drilled the entire intermediate section of the Tattoo field, located in Northwest Canada. An 8.5 (216mm) U513M drilled both the vertical and build sections with the same bottom hole assembly, saving the operator two trips and $72 per-meter versus the best offset and $570,000 when compared to the average of six section offsets in the...
Read More »
Choosing an Optimal Custom Label Printer: 5 Key Factors
Read about the 5 primary key factors you should consider when choosing an optimal label printer for your company.
Read More »Diamond Coring Bit is effective in hardest ground conditions.
Along with cutting matrix that enables penetration of hard rock formations in extreme conditions, 10UMX(TM) features Stage(TM) waterway design. Geometry of windows sustains integrity of bit through its entire life, allowing for variety of crown heights. Twin-Taper(TM) design improves surface flushing, forcing debris through windows while keeping bit face clear and reinforcing inner diameter....
Read More »
Solid Carbide Drills are for machining aerospace materials.
Feedmax(TM) -N solid carbide drills, suited for drilling in aluminum and non-ferrous materials, feature low-silicon coating that suits machining of aluminum with less than 10% silicone, as well as brass, zinc, and magnesium. Tools have conical front clearance with 12-
Read More »
Solid Carbide 30xD Drill suits deep hole drilling applications.
Available in diameters from 4-10 mm, Feedmax(TM) SD230A features 4-facet point geometry that provides optimal centering capability, with primary and secondary relief angles and point angle of 136-
Read More »Solid-Carbide Drills are optimized for deep hole applications.
Available with 15XD, 20XD, 25XD, and 30XD length ratios, WIDIA-Rubig(TM) deep-hole drills come in 3.0-13.0 mm diameters and do not require special drivers or guide bushings. Products can also be used in machining centers and are engineered to enhance material removal rate, hole quality, and cycle times. With 132-
Read More »
Seco Tools to Showcase Wide Range of Tooling Solutions at AeroDef Manufacturing 2011
Troy, Michigan - Seco Tools will be demonstrating a comprehensive range of tooling solutions for aerospace and defense applications at AeroDef Manufacturing 2011. The company will exhibit its products in booth #1778 at the event, which takes place April 5 - 7 at the Anaheim Convention Center in Anaheim, California. In recent years, Seco Tools has concentrated heavily on developing tooling...
Read More »
Solid Carbide Drills are designed for working with carbon fiber.
Feedmax(TM) drills avoid delamination upon entry or exit when drilling in carbon fiber reinforced polymer (CFRP) materials. While -C1 geometry features sharp, optimized double points, -C2 geometry is designed to drill stacked CFRP with aluminum or titanium outer layer. Polycrystalline diamond coating combats abrasive properties of CFRP while also promoting dimensional tolerance. Drills are 5xD,...
Read More »
Ensure Safety, Reliability in Your Cement Plant with Aerzen Blowers and Compressors
Aerzen offers blowers and compressors for challenging cement applications such as pneumatic conveying from raw mill to raw meal silos, combustion air, cement silos fluidization, and more. At Aerzen, safety is our top priority. Check out our video to learn more.
Read More »