New Electrical Equipment & Systems Products

Online UPS is floor or rack mounted.

Model S4K mounts directly into 19 in. rack, taking 2U of rack height, or can be floor-mounted for stand-alone applications. Standard input plug and 120 V output receptacles are easily removed, converting unit into fully hardwired UPS. Two-step battery charger extends battery life, while automatic or manual battery test feature warns when batteries need to be changed. Built-in communications allow...

Fanout Buffers accept any differential input.

Models SY89831, SY89832/3, and SY89834 are high-speed, precision LVPECL and LVDS 1:4 fanout buffers with internal termination. No external components are required in signal path. Highest throughput is >2 GHz, lowest jitter is

On-Board Battery Chargers offer simplified installation.

Industrial battery chargers use molded locking detent plugs to snap into locking tabs on back of ConnectCharge(TM) inlets. Inlets are available with spring-loaded flip lids or PVC flaps. Mounting options include threaded inlet sleeve with lock washer and front mounting. Chargers are suitable for industrial vehicles, lawn/farm equipment, electric bicycles, electric generator-sets, pumping...

Control Cables allows for up to 18 million flex cycles.

Available in unshielded and shielded versions, LEONI L-FLEXX 690 cables are 600 V, 90Ã-

Construction Materials for the Future

In this eBook, we highlight some key advantages of Cross-Laminated Timber (CLT) and show why every builder needs to consider adopting this remarkable construction advancement. We'll also introduce you to the latest innovation in CLT, GRIPBlock™, an exciting new technology that will change the way you look at CLT forever.

Power Supply helps meet CE requirements.

Single-output, 150 W open-frame Series RKW provides output voltages from 3.3-48 Vdc. Series conforms to EN 60950 for Low Voltage Directive and meets EN 55001-B and EN 55022-B standards for conducted and radiated emissions. Input harmonics are suppressed to meet EN 61000-3-2, by means of active Power Factor Correction (PFC) circuit. Series also meets all applicable Immunity and Susceptibility...

Edgeboard Connector requires no adhesive.

MCX E-Snap(TM) LP has small protrusions inside slot, allowing connector to securely snap into previously solder-pasted hole as it is slid onto board. Subminiature unit occupies only 2.7 mm above, and 1.06 mm below board. It features straight-through contact design, 50 ohm impedance, and repeatable performance to 18 GHz. Connector is suited for dense packaging arrangements and may be specified for...

Terminal Blocks provide vibration resistance.

Series 8113 pluggable spring-clamp PC board terminal blocks are available with molded-in screw flanges to ensure gas tight connections. Blocks are available in 2-16 poles and offer 5.0 and 5.08 mm spacings. Connectors, equipped with individual test points, are manufactured of polyamide 6.6 plastic housing, molded with scalloped mating areas to prevent mismating. Block are UL approved for 300 V,...

Italian Cordsets are offered in custom lengths.

Interpower(TM) Italian cordsets are configured with 16 A molded Italian plug and are terminated with 3 different angled IEC 60320 C19 connectors. Units are IMQ approved at 16 A/250 Vac and are available with 3 x 1.50 mmÃ-² cable.

Round Belts feature extended roll lengths.

Plastic belts are offered in coil lengths up to 3,280 ft, allowing runs of over six tenths of a mile, without splicing. They include KevlarÃ-®, steel, or polyester reinforcement. Kevlar reinforcement provides high strength can cable with flexibility, suitable for curved configurations. Belts are resistant to oil, grease, chemicals, dirt, and humidity.

Terminal Block provides gas tight connection.

Type AST025 SpringconÃ-® 5.00 mm spring clamp terminal block is rated to 300 V at 13 A and is available in circuit sizes from 2 to 24 poles. Design provides constact contact resistance and auto adjustment of spring force at each wire size. Unit accepts wire range from 14 to 28 AWG. It is UL and CSA listed and designed to meet VDE requirements.

Dodge® Raptor Coupling Now Available in Three Larger Sizes

The Dodge Raptor coupling epitomizes the innovation and value that has made Baldor a world leader in industrial electric motors. For almost 100 years Baldor has been the go-to source for industries across the globe. The Raptor coupling is just one example of our dedication to engineered excellence and commitment to providing value and performance. See our video to learn more.