Wire Stripping Machine handles difficult to strip insulation.
Stripper Machines

Wire Stripping Machine handles difficult to strip insulation.

Featuring menu-guided touchscreen interface and fully programmable parameters that can be stored or recalled in seconds, UniStrip 2550 strips wires ranging from 32-10 AWG and jacketed cables up to 0.22 in. in diameter. Machine comes standard with V blades for stripping most wires without having to change blades. For wires with difficult to strip insulations such as Teflon®, Kapton, and...

Read More »
Uncompromising Performance in a Carpet Extractor
Cleaning Equipment

Uncompromising Performance in a Carpet Extractor

The all-new HydraPort series of extractors from U.S. Products provides the uncompromising cleaning and extraction performance U.S. Products is famous for. The low-moisture/environmental-footprint-reduction system produces 212 degrees of heated cleaning solution from the in-line heater for faster carpet and hard-surface cleaning and drying. This also helps reduce chemical usage and the need for...

Read More »
Pneumatic Circular Saw dry cuts steel and non-ferrous metal.
Blades

Pneumatic Circular Saw dry cuts steel and non-ferrous metal.

Equipped with 2 hp pneumatic motor operating at 90 psi using 60 cfm air, Model 5 1115 0020 dry cuts steel plate up to 3/8 in. thick, as well as non-ferrous metal, plastic, grating, composite, and corrugated materials. Portable 9 in. saw has overall cutting depth of 3 Â-¼ in. at 90° and 2 1/8 in. at 45°. Measuring .055 in. thick, Laser Beam Saw Blade is tungsten-carbide tipped and...

Read More »
Vise Accessories provide for 30°, 45°, and 60° setups.
Vises

Vise Accessories provide for 30°, 45°, and 60° setups.

Used with standard 6 in. vise, Sine Parallels enable rectangle parts for machining to be clamped at 30°, 45° and 60° angles. They install and position with single bolt for each plate and jaw plates remain in vise while using them. Following initial setup, Sine Parallels can be changed to any other angle and also be used as a parallel. They also provide opportunity for clamping...

Read More »
Software

Lincoln Electric to Showcase Recent Innovations at the 2012 International Manufacturing Technology Show

Cleveland - Visitors to Lincoln Electric's booth at the 2012 International Manufacturing Technology Show (IMTS) will see the Company's leading edge robotic welding equipment, fume control technology and welding education innovations. IMTS 2012 will take place Sept. 10-15 at McCormick Place in Chicago. Lincoln Electric will be located in the North Hall at booth N-6618. The Company invites show...

Read More »
Gaylee Saws Will Be Exhibiting Their Line of Solid Carbide and Carbide-Tipped 'Thin Saws' at the 2012 IMTS
Blades

Gaylee Saws Will Be Exhibiting Their Line of Solid Carbide and Carbide-Tipped 'Thin Saws' at the 2012 IMTS

Sterling Heights, MI - Gaylee Saws will be exhibiting their line of solid carbide and carbide-tipped 'Thin Saws' at the 2012 IMTS Show at Booth W-2474 in the Tooling Pavilion. These high precision, tight tolerance thin saws provide dependable performance and extended tool life. Solid carbide saws from Gaylee Saws provide the ultimate combination of: o Maximum cutting speeds for minimum cost per...

Read More »
Storage/Dispensing/Cutting Solutions handle rolled materials.
Dispensers

Storage/Dispensing/Cutting Solutions handle rolled materials.

Used for storing single/multiple rolls of material, stands come in 6 standard widths from 30-80 in. and include free-standing, table-mounted, floor-mounted, and wall-mounted options. Bi-directional Cutting System provides safe operation, and leading edge of material is held in cutter to facilitate access. DS Series provides touchscreen PLC module for programming and operation. USB-compatible...

Read More »
Solid Carbide Micro Drill produces holes from 0.073-0.116 in. in diameter.
Drill Bits

Solid Carbide Micro Drill produces holes from 0.073-0.116 in. in diameter.

Featuring thin TiAlN coating that helps retain cutting edge geometry, CoroDrill 862 produces holes in steel, stainless steel, cast iron, and aluminum. Post treatment, combined with specially designed point geometry, minimizes thrust forces, while Advanced Chip Management flute geometry helps evacuate chips. Available in drill lengths of 8-12 x D, CoroDrill 862 achieves hole tolerance of IT8-IT9....

Read More »
The Gripper for a Variety of Gripping Diameters
Grippers (Tools)

The Gripper for a Variety of Gripping Diameters

Centric grippers with swivel fingers are an ideal solution if parts with various gripper diameters need to be alternately handled. Instead of exchanging top jaws or complete grippers every time, the fingers simply swivel into another position. With the PZH-SF 125, SCHUNK extends the program range of these versatile actuators with smaller sizes. At a diameter of 125 mm, the slim, long-stroke...

Read More »

All Topics