New Electrical Equipment & Systems Products

Safety System protects operators from electrical shock.

SmartGFI is able to recognize configuration of Device Under Test and automatically enable or disable GFI circuit accordingly. Circuit will shut down high voltage if leakage in excess of 450 microA is detected through grounding circuit. It disables high voltage in less than 1 ms. GFI circuit does not need to be manipulated by operator of instrument and therefore risk of operator error is...

Reed Relay has >10E+14 ohms insulation resistance.

Low-profile CR-Series leadless 50 Ohm reed relay switches at speeds up to 6 GHz with less than 40 ps rise times. To eliminate potential packaging stress, it is made with ceramic case that matches thermal coefficient of expansion of reed switch glass and reed lead. Capable of withstanding reflow soldering operations up to 260 deg C, it uses no internal solder, and has 1 microV typical thermal...

PCB Connectors suit GPS applications.

RTI-8300-04 right angle, MCX, female, surface mount PCB connector is suitable for 50 ohm applications with frequencies up to 6 Ghz. Snap-on mating provides rapid connects and disconnects. RMX-8300-04 offers gold plated machined brass body, gold plated contact, and TeflonÃ-® insulation. Suitable for space and weight-limited design criteria, MCX connectors are 30% smaller than SMB connectors,...

Flooded Battery provides backup power.

LCT II-1700 standby battery has floating epoxy post seal and solid copper posts to improve short duration rates of less than 5 hr. Applications include central office, Internet backup, data centers, outside plant, and wireless.

Choosing an Optimal Riot PPE Supplier: 5 Key Factors

This ebook provides 5 key factors to choosing an optimal riot PPE supplier.

Power Interface fits 1U power supplies.

Miniature, compact PCIC Series power connector has ac/dc input, signal, and output contacts in package measuring approximately 0.5 by 1.8 in. Input contacts carry 18 A at 30 deg C temperature rise. Contact terminations include right angle solder, straight solder and straight compliant press-fit. Options include ac pass-through version.

Hydraulic Power Unit drives bar shears.

VHPI-3 Hydraulic Power Unit, suitable for use with lightweight Bar Shears, weighs 30 lbs, and can be carried from one location to another. Fluid flow ranges from 1 GPM at low pressure to reduced flow at higher pressure. Its 1/2 HP motor draws 10 amps at 110 Volts.

Programmable Limit Switch offers .088 deg repeatability.

Compact multifunction PLS 1000 provides direct remote control of timing and dwell settings in applications that require events to occur in specific sequence. Microcomputer-based switch has brushless resolvers for absolute position feedback, 8 inputs and 16 programable high power outputs. Ten independent programs can be stored, changed, and initiated via splash-proof tactile keyboard, or RS232C...

Soft Shell Connectors are available in 2 to 12 positions.

Micro MATE-N-LOK 3mm-pitch connectors have dual-beam contacts for improved mating area, and high temperature housings for IR processing. Single row contacts on 3mm centerlines accommodate installations where thin, tight connectors capable of handling up to 5 A are required. Units can provide power and signal I/O and power interface interconnections.

Miniature Switch is suited for limited space applications.

EISM5-100T 5-port switching hub segments Ethernet network into 5 separate collision domains, acting as bridge to increase network diameter. One port can be used as uplink port to connect 2 hubs together, elminating need for crossover cable. Unit meets regulatory agency approvals and supports redundant power connections and low voltage AC or DC power sources. Activity/link/data rate LEDs exist for...

Interconnects combine differential and single ended systems.

Q-Pair high speed interconnects in differential pair configurations allow electrical performance at up to 5GHz operating frequencies. Connectors can be partitioned to include both differential pair and single-ended signal pins, allowing board designer to optimize system for high speed where required, while minimizing impact on density.

Micro Air's Dust, Fume, Mist Collection Equipment Facilitate a Safe Work Environment

Dust, fume, and mist collectors from Micro Air promote a safer, more productive work environment. Our wide array of products are available to the industrial manufacturing sector for processes such as welding, cutting, grinding, blasting, and more. Check out our video to learn more.