New Electrical Equipment & Systems Products

PFC Controller meets green requirements.

FAN4822 PFC employs zero-voltage switching control circuitry for efficient operation at high switching frequencies. Continuous boost architecture achieves power factor up to 98% and low total harmonic distortion necessary to comply with green initiatives, such as IEC 1000-3-2 standard for energy efficiency and noise reduction. Unit is rated for operation over -40 to +85 deg C, and is available in...

RS232-to-USB Cable updates serial devices.

US232 cable lets RS232 serial devices, such as old printers and bar code readers, connect to newer USB PCs. Based on FTDT's single chip FT8U232AM USB UART IC for transferring serial data over Universal Serial Bus, and Sipex SP213EHCA as its RS232 level converter, cable can support RS232 rates of up to 460 Kbaud. It comes with blue housing and Windows 98/2000/XP, Linux and iMAC drivers.

Insulation Displacement Connector requires no tools.

IDCON(R) connector provides secure gas tight connection, with no wire stripping and no screws. Modular Type AIT 01 accepts wire range of 26 to 22 AWG. It can be used multiple times and is available in variety of colors.

DC-DC Converters do not require heat sink.

Dual output, NKA03 3.3V subminiature DC-DC converters allow any distribution of load across outputs as long as total does not exceed 1W. Galvanic isolation of 3kVDC between input and outputs ensures minimum switching noise. Typical line regulation is rated at 1%, while typical ripple and noise current ratings are 30mA (peak-to-peak). Converters are supplied in fully encapsulated, UL 94V-0...

Managing the New FGD Wastewater Regulations

A guide for managing Flue Gas Desulfurization wastewater using leading technologies.

Power Cords have GOST approval.

Continental European powercords have 4.8 mm diameter pins, are stocked in 2.5 mm lengths, and are available with 3 x 1.00 mmE+02 or 3 x 1.5 mmE+02 cable. Powercords are rated for service between 10 and 16 amps at 250 Vac (depending on cord used).

Distribution Rack accommodates communications equipment.

Emcor(R) isoNet has 1/4 in. steel floor plates and top members, and 11 gauge steel uprights, providing sturdy mounts for 19 in. networking and data transmission equipment. Shelves can be single or double, and solid or vented for cooling. Patch cord cables can be organized and routed through horizontal-mounted cabling panel or wide, deep tray. Cable channels can be used to route cables between...

Connectors provide zero insertion force terminations.

VDE-certified Eco-Lock connector systems are designed for flexible flat cable/fine-pitch connector applications. Locking cover may be retracted to reopen contacts. Connectors are available in 4-30 pole configurations for 1 mm pitch surface-mount version and 5-35 poles for 1.25 mm pitch fork-type contact version. Both styles are available in horizontal and vertical configurations.

One-piece Interfaces connect to power boards.

OPP Series one-piece power interface, rated up to 5 A, eliminates bent pin problems of multi-component devices. Connectors are soldered to main board and power board is attached by either metric or English mechanical fasteners. Interfaces are available with choice of 3, 7 or 10 contacts on 0.100 in. pitch. Optional alignment pins can be provided on top, bottom or both sides to ease processing,...

Light Switch has built-in light sensor.

WS-200 passive infrared automatic wall switch turns lighting on and off based on occupancy and ambient light. Built-in light sensor holds electrical lighting off when natural light levels are above pre-set level. Infrared system uses pulse count processing and detection signature analysis to eliminate false triggers, reduce relay stress, and lengthen sensor life. Terminal style wiring eliminates...

I/O Modules support data acquisition.

Modules in I/O Pak(TM) family include C, K and DL Series. C-Series are 100Hz, 16-bit analog measurement devices with Modbus-RTU, Profibus-DP and simple ASCII communications options. K-Series are 1000Hz, 19-bit analog measurement devices that can be configured as Modbus or ASCII protocol slaves. DL-Series data logging modules with Modbus, Profibus and ASCII serial interface can log data from...

Dies & Stamping Services with Over 25 Years of Experience

PDS is an established leader in progressive die stamping, with a reputation for providing precision and value that dates back more than half a century. Through extensive capabilities and a staff of seasoned professionals, we set the standard for quality, delivering flexible services that can meet the needs of the most challenging requirements. See our video to learn more.