New Electrical Equipment & Systems Products

DC Gear Motor accepts any 12 Vdc power source.

Measuring 2.8 in. dia x 6 in. long, Model MMP.PDSF80-12V.180 features 80 mm square gearbox. Output shaft is 10 mm dia and is provided with square shaft key and keyway. Mounting is accomplished with 4 face-mounted threaded screws, 68 mm apart. Equipped with 180:1 gear ratio, motor is rated for 70 lb-in. of continuous torque at 3.9 A of current. Options include integral optical encoders, failsafe...

DC/DC Converter features 500 kHz operating frequency.

Housed in 6-lead SOT-23 package, Model LT1933 step-down converter includes internal 0.75 A power switch providing efficiencies as high as 88%. Input range of 3.6-36 V makes unit suitable for regulating power from wide variety of sources. Cycle-by-cycle current limit provides protection against shorted outputs, and soft-start eliminates input current surge during start up. Low current shutdown of...

Precision 2.92 mm Connector suits 40 GHz applications.

Model RF29M-SR1 consists of 50 ohm, 2.92 mm precision connector that can be used up to 46 GHz. It conforms to IEEE 287 standard, is mechanically compatible with SMA and 3.5 mm connectors, and features shortened male pin that ensures non-destructive mating process. Designed for .085 in., semi-rigid and high-performance flexible cable assemblies, product has gold-plated body and pin with molded...

Low-Voltage Transformers suit fan motors and controls.

Designed to meet need for reliable power for low-voltage circuits, inherently limited Class 2 Transformers are available with capacities of 5, 20, and 50 VA in 60 or 50/60 Hz ratings. Primary input voltages include 115, 115/230, and 200/230 V, with 12 V or 24 VCT outputs. While lead wires are standard, quick disconnect tabs are also available. Thermal fuses are standard on 20 and 50 VA models,...

Managing the New FGD Wastewater Regulations

A guide for managing Flue Gas Desulfurization wastewater using leading technologies.

Logic Gate Optocoupler suits high-speed applications.

Providing 5 kVrms isolation voltage over its power supply voltage range, FOD2200 allows designers to drive data buses directly and eliminates possibilities for output signal chatter. Low IF of 1.6 mA (min) and VCC range of 4.5-20 V make unit compatible with TTL, LSTTL, and CMOS logic. Housed in DIP-8 package, product features common mode rejection of 1 kV/5 s, 3-state output, hysteresis output,...

Connector is optimized for applications to 40 GHz.

Model RF29M-SR1 is a 50 ohm, 2.92 mm connector that conforms to IEEE 287 standard and is usable to 46 GHz. It is mechanically compatible with SMA and 3.5 mm connectors and has shortened male pin, ensuring non-destructive mating process. Designed for .085 in. semi-rigid cable assemblies, connector features gold-plated body and pin with molded dielectric bead and stainless steel coupling nut.

DC/DC Converter features isolated output.

Available with single, dual, or triple; low ripple; regulated outputs, 6E04 requires no external components for additional filtering. All versions feature pi input filters, 4:1 input voltage range, and CMOS/TTL compatible remote On/Off control for power conversion. Rated 25/35 W, converters achieve efficiencies to 80% due to 200 kHz+ switching frequencies. Single output converters have Output...

Gauging Sensor Head suits limited work envelopes.

Based on laser triangulation, SelcomÃ-® SLS 2401 offers stand-off distance of 1.97 or 3.15 in., depending on model, measuring range of 0.8 or 3.15 in., and spot size of 0.002 or 0.004 in. Class IIIb and optional Class II and Class 3R PSD-based unit features microprocessor-based Fast Light Control Circuit, which reacts in less than 8 Ã-µs for error-free measurements up to 16,000 times/sec....

Beam Clamp features finger-close smart nut.

CADDYÃ-® BCISN Beam Clamp enables easy installation of 3/8 in. threaded rod for attachment to beam flanges up to Ã-½ in. Without using tools or added nuts, clamp positions on 3/8 in. threaded rod and allows fine tuning and adjustment after rod is locked in place. Standard BC model supports Ã-¼ in. and 3/8 in. threaded rods, S-hooks, electrical boxes, conduits, and bridle rings. Both...

Wire Bonding Islands offer alternative to long wire bonding.

Gold-plated, Wire Bonding Islands can be mounted between 2 components being wired together using shorter wire leads, reducing overall parasitics in circuit. Units feature option of using tab for connection to circuit with standard thickness of 0.015 in. Made from alumina substrate, devices feature wire-bondable gold conductor, silver ground plane, and gold-plated, beryllium copper tab contact.

Neagle Choice, LLC Announces New Available Services

Neagle Choice has long been known as a quality source for commercial sewing, printing, die cutting, and the manufacturing of a wide range of custom products. Enhancing our service capabilities has been the key to our success, and has driven our growth into many new and exciting markets. Continuing on this trajectory, we now offer precision laser cutting and etching, adding to our long line of manufacturing services. See our video to learn all about it.